Loading...

Audi 80 Brake Bleeder Screw Caps

Audi 80 Brake bleeder screw caps

Brake bleeder screw caps for your Audi 80 start at $2.95, with 1 options in stock from URO. These small rubber or plastic caps press onto the tip of each bleeder screw to block moisture, road debris, and brake fluid residue from corroding the screw. A missing or cracked cap leads to seized bleeder screws that can make future brake bleeding difficult or impossible.

Signs your Audi 80 needs new brake bleeder screw caps

  • Bleeder screws are visibly bare, with no cap covering the tip
  • Existing caps are cracked, brittle, or flattened and no longer seat snugly
  • Dried brake fluid residue or rust buildup is visible around the bleeder screw tip
  • Bleeder screws are difficult to loosen or rounded off from corrosion caused by moisture intrusion
  • Caps are missing after a recent brake service or caliper replacement
  • Rubber caps have shrunk or hardened and fall off when touched

Which brake bleeder screw caps should you buy for your Audi 80?

The main decision is matching cap diameter to your bleeder screw tip size, since a loose cap provides no real protection. Material and whether you need individual caps or a bulk assortment are the other key factors worth considering before you buy.

OEM-matched single cap
Best for
Direct like-for-like replacement on a known screw size
What you get
Exact diameter fit for one bleeder screw position, factory material spec
Rubber assortment kit
Best for
Vehicles with mixed screw sizes or full axle refresh
What you get
Multiple diameters in one pack, flexible rubber that seals snugly on various tips
Silicone cap
Best for
High-heat environments or vehicles in harsh climates
What you get
Higher temperature resistance and longer service life than standard rubber
Plastic push-on cap
Best for
Budget replacement or temporary protection during service
What you get
Rigid fit, low cost, easy to install but less conforming than rubber or silicone

Brake bleeder screw caps brands we stock for your Audi 80

URO
1 option · from $2.95

Replacing brake bleeder screw caps on a Audi 80

Easy⏱ 5–15 minutesClean rag or shop towelWire brush or pick toolBrake cleaner sprayNeedle-nose pliers (to remove old stuck caps)

Clean any debris, rust, or dried brake fluid from around the bleeder screw tip using brake cleaner and a wire brush, then dry the area thoroughly. Press the new cap firmly over the screw tip until it seats flush — no tools or torque are required. Check that each cap is snug and cannot be pulled off by hand before finishing the job.

Frequently asked questions

How much does it cost to replace brake bleeder screw caps on a Audi 80?
Brake bleeder screw caps for a Audi 80 start at $2.95. Because they are consumable covers rather than structural components, this is one of the least expensive brake-related purchases you can make. Buying a small assortment kit typically covers all four corners of the vehicle for only a few dollars more.
Are brake bleeder screw caps necessary, or can I skip them?
Caps are necessary for long-term serviceability. Without them, moisture and road salt corrode the bleeder screw threads and the hex head. A seized bleeder screw can snap off inside the caliper during the next brake bleed, turning a routine maintenance task into a costly caliper replacement on your Audi 80.
How do I know what size bleeder screw cap fits my Audi 80?
Measure the outer diameter of your bleeder screw tip with a caliper, or check your Audi 80 service manual for the bleeder screw specification. Most passenger vehicles use screws that fall within a narrow common range, so an assortment kit from URO will typically cover the correct size without guesswork.
Can a missing bleeder screw cap cause a brake fluid leak?
A missing cap alone does not cause a brake fluid leak, because the bleeder screw itself must be open for fluid to escape. However, corrosion from an unprotected screw can cause it to weep fluid or crack when torqued, which can introduce a slow leak or air into the brake system of your Audi 80.
How often should bleeder screw caps be replaced on a Audi 80?
Replace bleeder screw caps any time you perform a brake service, bleed the brakes, or replace calipers on your Audi 80. Rubber and plastic caps degrade from heat cycling and UV exposure over time. Installing fresh caps after every brake service is a low-cost habit that protects far more expensive hardware.
Are brake bleeder screw caps universal, or vehicle-specific?
Caps are sized by the outer diameter of the bleeder screw tip, not by vehicle. A cap that fits the correct screw diameter will work on your Audi 80 regardless of brand. That said, always confirm the diameter matches, because an oversized cap will fall off and an undersized cap will split when pressed on.

Shop brake bleeder screw caps by year for the Audi 80

19921991199019891988

More parts for your Audi 80

StarterWheel Bearing Retaining RingHVAC Heater CoreStrut CartridgeEngine Timing CoverSerpentine BeltStabilizer Bar Bushing KitRack & Pinion Assembly

Brake bleeder screw caps for other Audi models

Audi A4 QuattroAudi A4 allroadAudi A5 QuattroAudi S6Audi Coupe QuattroAudi TT Quattro