Loading...

Audi 80 Strut Bumpers

Audi 80 Strut bumpers

Strut bumpers for your Audi 80 start at $15.95, and AutoBuffy stocks 2 options from Mevotech Supreme. The strut bumper is a polyurethane or rubber cushion that sits on the strut shaft inside the strut mount, absorbing the shock when the suspension bottoms out. When it crumbles or collapses, you get harsh clunking impacts, accelerated strut wear, and a jarring ride.

Signs your Audi 80 needs new strut bumpers

  • Loud clunk or thud from the front or rear suspension when hitting potholes, speed bumps, or dips at low to moderate speed
  • Harsh, bottoming-out sensation through the seat or floorboard that feels more abrupt than normal road harshness
  • Visible crumbling, flaking, or compressed polyurethane foam around the strut shaft when inspecting the strut assembly
  • Increased metal-to-metal contact noise during full suspension compression, such as when loading cargo or passengers
  • Accelerated wear on strut cartridges or shock absorbers caused by unprotected metal-to-metal impact at full droop or compression
  • Strut boot is torn or collapsed, exposing the bumper beneath and allowing dirt and moisture to degrade it further

Which strut bumper should you buy for your Audi 80?

The main decision is material and grade — OE-equivalent rubber, performance polyurethane, or a complete mount kit that bundles the bumper with the dust boot. Make sure the bumper matches the inner diameter and length spec for your Audi 80's strut shaft, since a bumper that is too short leaves a gap and one that is too stiff overloads the mount. Replacement as a pair (both fronts or both rears) keeps ride feel balanced.

OE-spec rubber bumper
Best for
Restoring factory ride quality on a daily-driven Audi 80
What you get
Soft, OEM-matched durometer that absorbs bottoming loads gently; direct fit to factory strut shaft dimensions
Polyurethane performance bumper
Best for
Audi 80 used for spirited driving, towing, or carrying heavy loads regularly
What you get
Firmer, longer-lasting material that resists compression set and holds up under repeated high-load impacts
Bumper + dust boot kit
Best for
Complete refresh when the boot is cracked or missing alongside the failed bumper
What you get
Both components in one box, matched in size; saves a return trip and protects the new bumper from day one
Complete strut mount kit (bearing + bumper + boot)
Best for
High-mileage Audi 80 where all upper strut components are worn together
What you get
Full upper strut rebuild in one purchase; eliminates multiple separate orders and ensures all parts fit together

Strut bumpers brands we stock for your Audi 80

Mevotech Supreme
2 options · from $15.95

Replacing strut bumpers on a Audi 80

Moderate⏱ 1.5–3 hours per axleFloor jack and jack standsSpring compressor (coil spring type)Socket set and breaker barTorque wrenchPry bar or trim tool for dust boot removal

Replacing strut bumpers on a Audi 80 requires removing the strut assembly from the vehicle, then using a spring compressor to safely collapse and remove the coil spring so the top mount, bearing plate, and bumper can be separated from the strut shaft. The old bumper slides off the shaft and the new one slides on before reassembly in reverse order. Because a compressed coil spring stores significant energy, this job should not be attempted without a proper spring compressor tool — improper technique can cause serious injury.

Frequently asked questions

How much does it cost to replace strut bumpers on a Audi 80?
Parts start at $15.95 for a single bumper on your Audi 80. Budget more if you replace bumpers in pairs or add dust boots. DIY labor is minimal since bumpers are accessed during a standard strut removal. Shop labor typically adds one to two hours per axle if you have the work done professionally.
How long do strut bumpers last on a Audi 80?
Strut bumpers on a Audi 80 generally last anywhere from 50,000 to over 100,000 miles, depending on road conditions, load habits, and material quality. Vehicles driven frequently on rough or unpaved roads, or regularly loaded near their payload limit, tend to wear bumpers much faster than those on smooth highway routes.
Can I drive my Audi 80 with a bad strut bumper?
You can drive short distances, but it is not advisable. A failed strut bumper allows metal-to-metal contact inside the strut assembly on every hard compression. This accelerates damage to the strut shaft, strut mount bearing, and surrounding suspension components, turning a low-cost bumper replacement into a significantly more expensive repair.
Do I need to replace strut bumpers in pairs on a Audi 80?
Yes, replacing in pairs is strongly recommended. Both bumpers on the same axle experience nearly identical stress over time, so if one has failed or crumbled, the other is typically in similar condition. Replacing only one leaves mismatched cushioning side to side, which can cause uneven ride height and handling pull.
Is a strut bumper the same as a jounce bumper on a Audi 80?
They are the same component referred to by two different names. Strut bumper, jounce bumper, and suspension bump stop all describe the cushioning sleeve that rides on the strut shaft and absorbs energy at full suspension compression. When shopping for your Audi 80, either term will lead you to the correct part.
Do I need to replace the strut to replace the bumper on a Audi 80?
No. The strut bumper is a separate, serviceable part that slides over the strut shaft and is replaced independently. You do need to disassemble the strut by removing the spring and top mount to access it, but the strut cartridge itself does not need to be replaced unless it is also worn or leaking.

Shop strut bumpers by year for the Audi 80

19921991199019891988

More parts for your Audi 80

StarterWheel Bearing Retaining RingHVAC Heater CoreStrut CartridgeEngine Timing CoverSerpentine BeltStabilizer Bar Bushing KitRack & Pinion Assembly

Strut bumpers for other Audi models

Audi S7Audi RS4Audi CabrioletAudi A8 QuattroAudi V8 QuattroAudi 90