Loading...

Bmw 1602 Tail Light Lens Seals

Bmw 1602 Tail light lens seals

Tail light lens seals for your Bmw 1602 start at $61.95, with 1 options in stock from URO. The seal is the rubber or foam gasket that sits between the tail light lens and the body panel, keeping water, road debris, and condensation out of the housing. A failed seal lets moisture in, causing bulb corrosion, lens fogging, and electrical shorts that can trigger warning lights.

Signs your Bmw 1602 needs a new tail light lens seal

  • Visible condensation or water droplets pooled inside the tail light housing after rain or a car wash
  • Foggy or cloudy lens interior that doesn't clear, indicating trapped moisture rather than surface grime
  • Rust streaks or corrosion on bulb sockets, bulb contacts, or the reflector backing inside the housing
  • Cracked, brittle, or visibly compressed rubber or foam gasket material around the lens perimeter
  • Tail light assembly smells musty or produces a burning odor when bulbs heat wet contacts
  • Recurring bulb failures or intermittent brake/turn-signal function caused by corroded sockets

Which tail light lens seal should you buy for your Bmw 1602?

The main decision is whether to match the original material and profile exactly or to go with a universal cut-to-fit strip. OE-profile seals fit without trimming and are the safest choice for a leak-free result; universal foam tape costs less but requires careful cutting and surface prep. Also confirm whether you need a driver-side, passenger-side, or both seals, as the two sides are often sold separately.

OE-profile replacement seal
Best for
Exact-fit, no trimming, fastest install
What you get
Pre-molded rubber or EPDM gasket matched to your Bmw 1602's housing shape and mounting groove
Universal foam tape seal
Best for
Budget repairs or discontinued OE seals
What you get
Self-adhesive closed-cell foam strip sold by the roll; must be measured, cut, and pressed into the channel by hand
Driver-side seal only
Best for
Replacing one failed side while the other is still intact
What you get
Single left-side gasket; confirm the damaged side before ordering to avoid a return
Pair (driver + passenger)
Best for
Both seals are cracked or the vehicle has high mileage
What you get
Both seals in one kit; more economical per side and ensures both housings seal evenly at the same time

Tail light lens seals brands we stock for your Bmw 1602

URO
1 option · from $61.95

Replacing tail light lens seals on a Bmw 1602

Easy⏱ 30–60 minutes per sideTrim panel removal tool or flathead screwdriver with tape paddingPhillips or Torx screwdriver (varies by vehicle)Isopropyl alcohol and clean ragsScissors or utility knife (for universal foam seals)Compressed air or clean towel for drying the housing

Open the trunk or tailgate to access the tail light mounting hardware, remove the retaining screws or push-pins, and pull the housing away from the body. Peel out the old gasket from its channel, clean the groove and mating surface with isopropyl alcohol, and allow it to dry fully before pressing the new seal in place. Reinstall the housing, confirm the lens seats evenly against the body panel with no gaps, and check that all lights function before closing up.

Frequently asked questions

How much does it cost to replace tail light lens seals on a Bmw 1602?
Parts start at $61.95 for a Bmw 1602 tail light lens seal. Most owners replace both sides at once, so budget for two seals. Installation is typically a DIY job requiring no special tools, keeping total cost low. Shop labor, if used, is usually billed as less than one hour.
Can I drive my Bmw 1602 with a failed tail light lens seal?
You can drive short-term, but it is not advisable. A leaking seal allows water to reach bulb sockets and wiring, which corrodes contacts and can cause brake or turn-signal failures — a safety and legal issue. Prolonged moisture exposure can also damage the entire tail light assembly, turning a cheap seal fix into a costly housing replacement.
Will replacing the seal clear up the condensation already inside my Bmw 1602's tail light?
Yes, but you must dry the housing completely before installing the new seal. Remove the assembly, wipe out standing water, and let it air-dry or use compressed air on low pressure. Sealing moisture inside will keep the lens foggy. Once sealed correctly, trapped humidity dissipates and the lens should clear within a few days of normal use.
How long do tail light lens seals last on a Bmw 1602?
Factory seals typically last many years under normal conditions, but rubber and foam degrade faster in climates with extreme heat, UV exposure, or road-salt use. General lifespan ranges from several years to the life of the vehicle. Inspect the gasket whenever you change a tail light bulb — compression set, cracking, or shrinkage are signs it is time to replace.
Do I need to replace the entire tail light assembly or just the seal on my Bmw 1602?
In most cases you only need the seal. Replace the full housing only if the lens is cracked, the reflector is damaged, or corrosion has destroyed the bulb sockets. If the housing is otherwise clean and intact, a new seal restores a weatherproof fit at a fraction of the cost of a complete assembly replacement.
How do I know which tail light lens seal fits my Bmw 1602?
Match by year, make, and model, and confirm the side — driver or passenger. Some Bmw 1602 models use different seals for inner and outer housings on three-piece tail light setups, so check whether your application has a single-piece or multi-piece lens before ordering. Using the AutoBuffy year-make-model selector filters 1 seals down to confirmed-fit options.

Shop tail light lens seals by year for the Bmw 1602

19711970196919681967

More parts for your Bmw 1602

Electric Fuel PumpTie Rod EndSubframe MountCoil Spring ShimQuarter Glass SealRadiator Coolant HoseBrake Hardware KitEngine Mount

Tail light lens seals for other Bmw models

Bmw 2002Bmw 2002tii