Loading...

Bmw 328Ci Engine Valve Cover Mounts

Bmw 328Ci Engine valve cover mounts

Engine valve cover mounts start at $22.95 at AutoBuffy, where you'll find 1 options from brands including URO. These rubber-isolated fasteners and grommets seal and cushion the valve cover against the cylinder head, dampening vibration and preventing oil leaks. When they deteriorate, you get oil seeping onto hot exhaust components, rough idle, and potential engine damage.

Signs your Bmw 328Ci needs new engine valve cover mounts

  • Visible oil residue or wet staining around the perimeter of the valve cover, often dripping onto the exhaust manifold or spark plug wells
  • Burning oil smell from the engine bay, caused by oil contacting hot exhaust surfaces after leaking past a failed mount or grommet
  • Oil-fouled spark plugs leading to misfires, rough idle, or a check-engine light with misfire codes
  • Audible ticking or tapping from the top of the engine, sometimes caused by a loose valve cover vibrating against the head when mount grommets collapse
  • Cracked, hardened, or visibly deformed rubber grommets around the valve cover bolts when inspected visually
  • Persistent low oil level without a clear external leak — oil may be burning off after seeping onto hot components rather than pooling on the ground

Which engine valve cover mount should you buy for your Bmw 328Ci?

The main decision is whether you need individual bolt grommets, a complete mount kit with hardware, or an OEM-equivalent assembly. Material quality matters most here — cheap mounts harden and crack quickly from heat cycling, so matching or exceeding the original rubber compound is worth the small price difference.

OEM-spec rubber grommets (individual)
Best for
Direct replacement of worn grommets only, keeping original bolts
What you get
Single or sets of rubber isolator grommets matched to original dimensions and durometer rating
Complete mount kit with bolts and grommets
Best for
Full refresh when bolts are stripped or corroded alongside failed grommets
What you get
All fasteners and grommets needed in one box; simplifies the job and ensures matched components
Silicone-compound grommets
Best for
High-heat applications or engines with histories of premature grommet failure
What you get
Superior heat and oil resistance compared to standard rubber; longer service life in demanding conditions
OEM dealer part
Best for
Exact factory fit with no guesswork on material or geometry
What you get
Part engineered to the manufacturer's original specification; higher cost but guaranteed compatibility

Engine valve cover mounts brands we stock for your Bmw 328Ci

URO
1 option · from $22.95

Replacing engine valve cover mounts on a Bmw 328Ci

Easy⏱ 30–90 minutesSocket set and ratchetTorque wrenchFlathead screwdriver or pick tool (for grommet removal)Clean lint-free ragsBrake cleaner or parts cleaner

Remove any covers or components blocking access to the valve cover, then loosen and remove all valve cover bolts and lift the cover clear. Press the old grommets out with a pick or screwdriver, clean all mating surfaces thoroughly, and seat the new grommets before reinstalling the cover with a new gasket. Snug the bolts gradually in a cross-pattern and tighten to the manufacturer's specified range — overtightening is a common mistake that immediately damages the new grommets.

Frequently asked questions

How much does it cost to replace engine valve cover mounts on a Bmw 328Ci?
Parts start at $22.95 for individual grommets on a Bmw 328Ci. A complete kit with bolts and grommets typically costs more but can save labor time. DIY installation is straightforward for most vehicles, keeping total cost close to the parts price alone if you do the work yourself.
Can I drive my Bmw 328Ci with a failed valve cover mount?
Short distances are possible, but it is not recommended. A leaking valve cover mount allows oil to drip onto hot exhaust components, creating a fire risk and accelerating oil consumption. Oil reaching spark plug wells can foul plugs and cause misfires. Address the repair promptly to avoid secondary damage.
Do I need to replace all valve cover mount grommets at once on my Bmw 328Ci?
Yes, replacing all grommets at the same service is the correct approach. Grommets age from the same heat cycles and oil exposure, so if one has failed the others are close behind. Replacing them as a set ensures an even seal across the entire valve cover and avoids a repeat job shortly after.
Will a new valve cover gasket fix my leak, or do I also need new mounts?
Both parts often fail together and should be inspected simultaneously. The valve cover gasket seals the mating surface between the cover and head, while the mount grommets seal and isolate each bolt hole. A new gasket with collapsed grommets will still leak at the bolt points, so replacing both together is the correct repair.
How long do engine valve cover mounts last on a Bmw 328Ci?
Service life varies widely depending on engine heat, oil type, and climate, but rubber grommets generally last anywhere from several years to well over a decade. High-temperature engines and vehicles that see frequent short trips accelerate heat cycling and can shorten lifespan. Inspect them whenever the valve cover gasket is serviced.
Are aftermarket valve cover mounts as good as OEM for a Bmw 328Ci?
Quality aftermarket mounts from reputable brands like URO are engineered to match or exceed OEM durometer and heat resistance ratings. Avoid the lowest-cost options with no material specification listed. A silicone-compound mount from a known brand will often outlast the original rubber part, especially on engines that run hot.

Shop engine valve cover mounts by year for the Bmw 328Ci

2000

More parts for your Bmw 328Ci

Mass Air Flow SensorA/C System Repair KitLicense Plate BracketBrake Hydraulic HoseManual Transmission Shift KnobPCV Valve GrommetTire Pressure Monitoring System (TPMS) Programmable SensorAir Bag Clockspring

Engine valve cover mounts for other Bmw models

Bmw 325CiBmw 530iBmw 330CiBmw 328isBmw 330xiBmw M3