Loading...

Bmw 550I Gt Fuel Tank Breather Valves

Bmw 550I Gt Fuel tank breather valves

Starting at $112.95, AutoBuffy stocks 1 fuel tank breather valves from URO. This valve vents pressure and vacuum from the fuel tank while blocking liquid fuel and excess vapors from escaping into the atmosphere. When it fails, the tank can collapse under vacuum or over-pressurize, causing hard starts, fuel leaks, and failed emissions tests.

Signs your Bmw 550I Gt needs a new fuel tank breather valve

  • Fuel tank visibly collapsed, deformed, or making a loud creak when the fuel cap is removed
  • Strong fuel vapor smell near the rear of the vehicle, especially after sitting in the sun
  • Engine hesitates or stalls shortly after starting, then runs normally once the fuel cap is loosened
  • Repeated evaporative emission (EVAP) fault codes such as large or small leak detected
  • Fuel gauge reads erratically or the fuel pump whines louder than usual under load
  • Difficulty refueling — the pump nozzle kicks off repeatedly as if the tank is already full

Which fuel tank breather valve should you buy for your Bmw 550I Gt?

The main decision is whether to match OE specifications exactly or upgrade to a higher-flow aftermarket unit. Fit and cracking pressure rating must be correct for your Bmw 550I Gt's EVAP system, or you risk the same codes and symptoms returning. Also confirm whether your application uses a standalone breather valve or one integrated into a rollover/fuel cutoff valve assembly.

OE-Equivalent Replacement
Best for
Restoring factory EVAP performance and passing inspection
What you get
Exact cracking pressure, identical port sizing, and direct bolt-on fit with no modification
OEM Supplier (Tier-1 Brand)
Best for
Owners who want factory quality without dealer pricing
What you get
Parts made to OEM spec by the same suppliers that built the original, often at a lower cost
Integrated Rollover Valve Assembly
Best for
Vehicles where the breather and rollover valve share one housing
What you get
Single-unit replacement that eliminates the need to source two separate parts and reduces leak points
High-Flow Aftermarket
Best for
Modified vehicles with upgraded fuel systems or higher-capacity tanks
What you get
Increased vapor flow capacity to match upgraded components; may require minor hose adaptation

Fuel tank breather valves brands we stock for your Bmw 550I Gt

URO
1 option · from $112.95

Replacing the fuel tank breather valve on a Bmw 550I Gt

Moderate⏱ 1–2 hoursSafety glasses and nitrile glovesJack stands or vehicle liftTrim removal tool or flathead screwdriverHose clamp pliersFlashlight or work light

Begin by depressurizing the fuel system and disconnecting the battery to eliminate ignition sources, then locate the breather valve on top of or alongside the fuel tank. Disconnect the vapor hose or hoses from the valve, release any retaining clip or bracket, and swap in the new unit before reconnecting hoses and verifying a snug, leak-free fit. After reassembly, clear any stored EVAP fault codes and run a complete EVAP monitor drive cycle to confirm the repair.

Frequently asked questions

How much does it cost to replace fuel tank breather valves on a Bmw 550I Gt?
Parts start at $112.95 at AutoBuffy. A shop will typically add one to two hours of labor on top of the part cost, since the valve is often located on or near the top of the tank and may require partial tank removal. DIY replacement keeps the total cost close to the part price alone.
Can I drive my Bmw 550I Gt with a bad fuel tank breather valve?
Short trips are possible, but continued driving risks tank deformation from vacuum buildup, which is an expensive secondary repair. A failing valve will also keep your Bmw 550I Gt in a permanent check-engine or EVAP fault state, and fuel vapor leaks present a fire hazard. Replacement should not be deferred for long.
Will a faulty breather valve cause my Bmw 550I Gt to fail an emissions test?
Yes. The breather valve is part of the EVAP system, and a leak or blockage typically triggers a stored fault code. Most OBD-II emissions tests will fail a vehicle with an active or pending EVAP code. Replacing the valve and completing a full EVAP monitor drive cycle is required before retesting.
How long does a fuel tank breather valve last on a Bmw 550I Gt?
Most breather valves last many years under normal conditions, but heat cycling, ethanol-blend fuels, and road debris accelerate wear. Valves on vehicles driven in extreme heat or used with high-ethanol fuel blends tend to harden and crack sooner. Inspect the valve whenever EVAP codes appear rather than on a fixed interval.
Is the fuel tank breather valve the same as the EVAP canister vent valve on a Bmw 550I Gt?
No, they are different components. The breather valve is a passive one-way or two-way vent mounted directly on the tank that controls pressure balance. The canister vent valve is an electrically actuated solenoid that controls airflow through the charcoal canister. Both are part of the EVAP system but serve distinct functions and fail in different ways.
Do I need to drop the fuel tank to replace the breather valve on a Bmw 550I Gt?
It depends on the mounting location. On many Bmw 550I Gt applications the breather valve sits on top of the tank with hose connections accessible from above or through a trunk or bed access panel, making removal straightforward. On others, the tank must be lowered to reach the valve. Check the routing before starting the job.

Shop fuel tank breather valves by year for the Bmw 550I Gt

201220112010

More parts for your Bmw 550I Gt

Engine Mount KitRack & Pinion AssemblyVacuum PumpHVAC Pressure TransducerDome Light ConnectorFuel Pressure SensorEngine Variable Valve Timing (VVT) SolenoidEngine Cylinder Head Gasket

Fuel tank breather valves for other Bmw models

Bmw 750iLBmw 330iBmw 750LiBmw 335i xDriveBmw 740LiBmw X3