Loading...

Bmw M6 Emblem Retainers

Bmw M6 Emblem retainers

Starting at $20.95, AutoBuffy stocks 1 emblem retainers from URO to keep the badges on your Bmw M6 firmly in place. An emblem retainer is the clip, push-pin, or bracket that anchors a nameplate or logo to body panels. When it fails, emblems loosen, rattle, or fall off entirely — leaving adhesive residue and exposed holes that invite rust.

Signs your Bmw M6 needs a new emblem retainer

  • A hood, trunk, or door badge visibly shifts or tilts when touched or during driving
  • You can hear a faint plastic rattling from a body panel at highway speeds that stops when you press the badge flat
  • The emblem pops out entirely and leaves one or more open mounting holes in the sheet metal
  • The retainer clip is visibly cracked, broken in half, or missing its locking tab when you remove the badge to inspect
  • The badge sits unevenly — one corner flush, the opposite corner standing proud of the panel surface
  • Rust or surface corrosion is forming around an exposed mounting hole where a retainer is no longer sealing the panel

Which emblem retainer should you buy for your Bmw M6?

Emblem retainers are not universal — clip style, shank diameter, head size, and material all vary by vehicle line and badge location. The right choice depends on whether you are replacing a broken clip, reattaching a loose badge, or doing a full emblem swap. Match the retainer type to the mounting method the factory used on your Bmw M6.

OEM-Style Push-Pin Retainer
Best for
Exact factory replacement where the original clip snapped in
What you get
Correct shank diameter and head profile to seat flush in the factory-drilled hole without modification
Rivet-Style Retainer
Best for
High-vibration locations such as front grilles and truck tailgates
What you get
One-way locking body that resists pull-out under road vibration better than standard push-pins
Screw-In / Threaded Retainer
Best for
Emblems that were originally bolted rather than clipped, common on larger nameplates
What you get
Metal or hard-nylon threaded body that provides stronger holding force and allows future removal without destroying the retainer
Adhesive-Backed Retainer Plate
Best for
Panels where original holes are stripped, damaged, or where you want a no-drill mounting solution
What you get
Double-sided foam tape combined with a locating stud so the badge aligns correctly while the adhesive bond provides the primary hold

Emblem retainers brands we stock for your Bmw M6

URO
1 option · from $20.95

Replacing emblem retainers on a Bmw M6

Easy⏱ 15–45 minutesPlastic trim pry tool or wide-blade trim removerHeat gun or hair dryerIsopropyl alcohol and clean microfiber clothsNeedle-nose pliers (for extracting broken shank stubs)Masking tape (to protect surrounding paint)

Remove the badge by warming the panel to loosen adhesive, then lever it free with a plastic trim tool to avoid scratching the paint. Extract any broken retainer stubs from the mounting holes using needle-nose pliers, clean the holes and panel surface thoroughly, then press the new retainers into the holes until they click, and seat the badge firmly onto the retainer shanks.

Frequently asked questions

How much does it cost to replace emblem retainers on a Bmw M6?
Parts start at $20.95 for a set of retainer clips. Most drivers do this job themselves in under 30 minutes with no special tools, so there is no labor cost. If a body shop replaces them during a paint or bodywork visit, expect a small flat labor charge on top of the part price.
Can I reuse the old emblem retainers on my Bmw M6?
Usually no. Plastic push-pin retainers have a one-time locking tab that deforms or snaps when the badge is pried off. Reusing a sprung or cracked clip risks the emblem loosening again quickly. Metal screw-in retainers are the exception — inspect threads carefully and replace any that are stripped or corroded.
Will a missing emblem retainer let water into the body panel on a Bmw M6?
Yes. An open mounting hole bypasses the factory paint and primer, exposing bare metal directly to water and road salt. Even a small hole can develop surface rust within one to two seasons in wet climates. Replacing the retainer closes the hole and restores the factory seal around the badge shank.
How do I remove the old emblem without breaking the panel on my Bmw M6?
Warm the badge and surrounding panel gently with a heat gun on low to soften any adhesive backing, then use a wide plastic trim pry tool or dental floss to work behind the emblem gradually. Avoid metal tools against painted surfaces. Once the badge is off, use an adhesive eraser wheel or isopropyl alcohol to clean residue before installing new retainers.
Are emblem retainers sold individually or as a set for the Bmw M6?
Both options are available. Single retainers suit situations where only one clip broke. Full sets — typically four to ten clips depending on badge size — are the better value when you are reattaching an emblem completely or doing a multi-badge job. Check the listing carefully to confirm quantity before ordering.
Do aftermarket emblem retainers fit as well as factory parts on a Bmw M6?
Quality aftermarket retainers use the same shank diameter and locking geometry as the OEM clip and fit identically in most cases. Stick with retainers listed specifically for your Bmw M6 year range rather than universal packs, which may require trimming or shimming to achieve a flush, rattle-free fit.

Shop emblem retainers by year for the Bmw M6

19881987

More parts for your Bmw M6

Engine Auxiliary Water PumpEngine Cylinder Head Temperature SensorHVAC Heater CoreAcceleration SensorA/C Evaporator CoreEngine Timing Chain TensionerLateral Arm BushingA/C Line O-Ring

Emblem retainers for other Bmw models

Bmw 535iBmw 2800Bmw 850CSiBmw 325esBmw 735iLBmw 2500