Loading...

Bmw X3 Fuel Injection Throttle Body Assemblys

Bmw X3 Fuel injection throttle body assemblys

Starting at $162.95, AutoBuffy stocks 2 fuel injection throttle body assemblies from URO. The throttle body controls how much air enters your Bmw X3's engine in response to accelerator input. When it fails or becomes fouled, the engine management system loses precise air control, causing rough idle, hesitation, and poor fuel economy that won't improve until the unit is cleaned or replaced.

Signs your Bmw X3 needs a new fuel injection throttle body assembly

  • Rough or unstable idle that surges up and down at a stop
  • Hesitation or stumbling when you press the accelerator from a standstill
  • Check engine light with codes related to throttle position (P0120–P0124) or idle control
  • Poor fuel economy with no other obvious cause
  • Engine stalls at idle or immediately after cold starts
  • Unresponsive or sticky throttle feel, especially during light throttle inputs

Which fuel injection throttle body assembly should you buy for your Bmw X3?

The biggest decision is whether to buy an OEM-equivalent remanufactured unit, a new aftermarket assembly, or a genuine OEM part. For most Bmw X3 owners, a new or remanufactured assembly is the practical choice — the throttle position sensor (TPS) and idle air control components are pre-installed and pre-calibrated, so you avoid separate sourcing and calibration hassles.

New OEM (dealer)
Best for
Owners who want factory-exact fit and calibration with no guesswork
What you get
Original specs, pre-set TPS, full warranty — highest cost
New Aftermarket
Best for
Budget-conscious owners who still want an uninstalled, fresh unit
What you get
New components, meets OEM specs, lower price than OEM, wider brand variety
Remanufactured
Best for
Value seekers comfortable with a professionally rebuilt unit
What you get
Cleaned, re-bored bore, replaced seals and sensors, tested — mid-range price
Throttle Body + Sensor Kit
Best for
DIYers replacing a failed TPS alongside a worn body at the same time
What you get
Complete assembly with sensor included, eliminates separate parts ordering

Fuel injection throttle body assemblys brands we stock for your Bmw X3

URO
2 options · from $162.95

Replacing a fuel injection throttle body assembly on a Bmw X3

Moderate⏱ 1–2 hoursSocket and ratchet setFlat-head and Phillips screwdriversNeedle-nose pliers (for hose clamps)Throttle body cleaner and clean ragsOBD-II scan tool (for throttle relearn on drive-by-wire systems)

Disconnect the battery, then remove the air intake duct and any connected vacuum lines or coolant hoses, labeling each for reinstallation. Unbolt the throttle body from the intake manifold, disconnect the electrical connector, and install the new assembly with a fresh gasket, tightening the bolts evenly in a cross pattern to avoid warping. Reconnect all hoses and wiring, then perform the manufacturer-specified throttle body relearn procedure before returning the vehicle to service.

Frequently asked questions

How much does it cost to replace fuel injection throttle body assemblies on a Bmw X3?
Parts start at $162.95 on AutoBuffy. A complete DIY replacement costs only the part price. At a shop, labor typically adds one to two hours of shop time on top of the part cost. Choosing a remanufactured or aftermarket unit instead of OEM can significantly reduce your total bill without sacrificing reliability.
Can I clean the throttle body instead of replacing it on my Bmw X3?
Cleaning is the right first step if the bore and butterfly plate are just coated with carbon deposits and the throttle position sensor still reads accurately. Use throttle body cleaner and a soft cloth with the battery disconnected. If idle problems persist after cleaning, or if the TPS or motor is faulty, replacement is necessary.
Do I need to relearn or reset the throttle body after replacing it on a Bmw X3?
Yes, on most modern Bmw X3 applications a throttle body relearn procedure is required after installation. This tells the ECU the new baseline throttle position at rest. Some vehicles complete this automatically after an idle warm-up cycle; others require a scan tool to run a specific relearn routine. Skipping this step often causes rough idle or error codes.
What causes a throttle body to fail on a Bmw X3?
The most common causes are carbon buildup restricting the butterfly valve, a worn or failed throttle position sensor, a faulty idle air control motor, and internal gear wear in drive-by-wire units. Infrequent air filter changes and oil blow-by from the PCV system accelerate carbon accumulation and are the leading contributors to premature throttle body failure.
Is it safe to drive my Bmw X3 with a bad throttle body?
It is not recommended. A failing throttle body can cause sudden stalling, unpredictable acceleration response, or cause the ECU to put the Bmw X3 into a reduced-power limp mode. Any of these conditions can be dangerous in traffic. Drive only as needed to reach a repair location, and avoid highway or high-speed driving until the part is replaced.
Will any throttle body fit my Bmw X3, or does it have to match exactly?
The replacement must match your engine's bore diameter, connector type, and control method — cable-actuated versus electronic drive-by-wire units are not interchangeable. Always use your Bmw X3's year, make, model, and engine size to confirm fitment before ordering. Using AutoBuffy's vehicle selector ensures you see only compatible assemblies for your specific application.

Shop fuel injection throttle body assemblys by year for the Bmw X3

20172016201520142013201220112010200920082007

More parts for your Bmw X3

Wheel Bearing Retaining RingParking Brake Cable GuideLiftgate Lift SupportTransfer Case MountSuspension KitSuspension Strut Brace Bracket Cover CapEngine Oil FilterEngine Cylinder Head Temperature Sensor

Fuel injection throttle body assemblys for other Bmw models

Bmw 328xiBmw 323iBmw 320iBmw 228iBmw X4Bmw 328i xDrive