Loading...

Bmw X6 Control Arm Repair Kits

Bmw X6 Control arm repair kits

Starting at low prices, AutoBuffy stocks multiple control arm repair kits from top OE-quality brands for the Bmw X6. A control arm repair kit replaces the worn bushings and ball joints that connect the control arm to the chassis and wheel hub. When these components fail, steering becomes imprecise and tire wear accelerates — leaving the suspension unable to maintain proper wheel alignment.

Signs your Bmw X6 needs a control arm repair kit

  • Clunking or knocking noise from the front suspension over bumps or during turns
  • Steering wheel pulls to one side consistently, even on a flat, straight road
  • Uneven or rapid tire wear on the inner or outer edge of the front tires
  • Vibration felt through the steering wheel at highway speeds that worsens on rough pavement
  • Loose or vague steering feel, especially noticeable during lane changes or cornering
  • Visible cracking, tearing, or separation of the rubber control arm bushings on inspection

Which control arm repair kit should you buy for your Bmw X6?

Control arm repair kits vary by what's included — some replace only the bushings, others add a ball joint or the full hardware set. Match the kit to whichever components are actually worn on your Bmw X6 to avoid paying for parts you don't need. Position (front upper, front lower, rear) and OE-vs-performance grade are the two other decisions that narrow the field.

Bushing-only kit
Best for
Control arm is undamaged; only the rubber or polyurethane bushings are cracked or worn
What you get
Replacement bushings and hardware; lowest cost repair that restores isolation and alignment geometry
Bushing + ball joint kit
Best for
Both the bushing and ball joint show wear at the same time, common on high-mileage vehicles
What you get
Matched bushing and ball joint in one box, ensuring both pivot points are renewed together
Complete control arm repair kit (full hardware)
Best for
Heavy wear, torn boots, and corroded bolts all at once, or a pre-MOT restoration
What you get
Bushings, ball joint, boot, retaining clips, and fasteners — everything needed for a single-visit repair
Performance / polyurethane bushing kit
Best for
Track use, towing, or drivers who prefer sharper steering response over ride comfort
What you get
Stiffer poly bushings that resist compression better than rubber, improving handling precision at the cost of slightly more NVH

Replacing a control arm repair kit on a Bmw X6

Advanced⏱ 2–4 hoursFloor jack and jack standsBreaker bar and socket setBall joint press or bushing press kitPickle fork or ball joint separatorTorque wrench

Removing the old bushings requires a hydraulic press or a dedicated bushing press kit — attempting to drive them out with a hammer risks damaging the control arm housing. Once the new bushings and ball joint are pressed in and the arm is reinstalled, all suspension fasteners should be torqued with the suspension at ride height, not hanging, to prevent premature bushing tear. A professional alignment must follow the repair to restore correct geometry.

Frequently asked questions

How much does it cost to replace control arm repair kits on a Bmw X6?
Parts alone start at low prices for a Bmw X6 control arm repair kit. A full DIY repair typically costs only the kit price plus consumables like penetrating oil. Shop labor adds roughly one to two hours of labor time on top of parts, depending on corrosion and whether one or both sides are being done.
Can I replace just the bushings, or do I need the whole control arm on my Bmw X6?
If the control arm itself is straight and uncracked, replacing just the bushings — and the ball joint if it's worn — is the correct repair and costs significantly less than a full arm. Inspect the arm for bending, cracks near the ball joint housing, or corrosion-through before deciding. A repair kit is the right call when the arm is structurally sound.
How long do control arm bushings last on a Bmw X6?
Rubber control arm bushings typically last somewhere between 50,000 and 100,000 miles, though road salt, off-road use, and frequent heavy loads shorten that range considerably. Polyurethane bushings generally outlast rubber but transmit more vibration. Inspect bushings any time tires are rotated or alignment is checked to catch cracks early.
Is it safe to drive a Bmw X6 with a worn control arm bushing?
A mildly cracked bushing can be driven short distances to a shop, but a fully separated bushing or a worn ball joint is a safety risk. The wheel can shift unpredictably under braking or cornering loads. If you hear a loud clunk, feel steering wander, or see a torn bushing boot, stop driving and repair the Bmw X6 promptly.
Do I need an alignment after replacing the control arm repair kit on my Bmw X6?
Yes — a four-wheel alignment is required after any control arm bushing or ball joint replacement. Disturbing the suspension changes camber and caster settings, even if only slightly. Skipping the alignment risks accelerated and uneven tire wear and can make the Bmw X6 pull to one side immediately after the repair.
Should I replace control arm repair kits on both sides at the same time?
Replacing both sides together is the recommended practice when one side is worn, because the opposite bushing has the same mileage and stress history. Matching both sides also keeps handling balanced and avoids a pulling condition caused by unequal bushing stiffness. The labor overlap makes doing both at once the more cost-effective choice.

More parts for your Bmw X6

Air / Fuel Ratio SensorRide Height SensorSubframe BushingFuel Injection Nozzle O-Ring KitEngine Oil FilterHeadlight Halo Ring Emitter SetStrut BumperParking Brake Actuator

Control arm repair kits for other Bmw models

Bmw 335iBmw 750iLBmw 740iLBmw 550iBmw 328dBmw 228i xDrive Gran Coupe