Loading...

Buick Century Air Bag Sensor Connectors

Buick Century Air bag sensor connectors

Starting at low prices, AutoBuffy carries multiple air bag sensor connectors from top OE-quality brands that fit the Buick Century. This connector links the crash or impact sensor to the SRS control module, allowing the airbag system to fire in a collision. A damaged or corroded connector can prevent airbag deployment or trigger a constant fault code, making replacement a safety-critical repair.

Signs your Buick Century needs a new air bag sensor connector

  • SRS or airbag warning light stays on after clearing codes with no other faults found
  • Diagnostic scanner shows an open circuit or low-voltage fault specific to a crash or impact sensor
  • Airbag system enters fault mode after driving over bumps or rough roads, suggesting an intermittent connection
  • Visible corrosion, melted plastic, bent terminals, or broken locking tabs on the existing connector body
  • SRS warning light returns within a short drive after the code is cleared, pointing to a wiring connector rather than the sensor itself
  • Clockspring or side-impact sensor tests good when bench-tested but throws a circuit fault when reinstalled, isolating the fault to the connector

Which air bag sensor connector should you buy for your Buick Century?

The most important buying decision is matching the connector to the exact sensor position — front impact, side impact, or rollover — because terminal count, locking tab style, and wire gauge differ between locations. You also need to choose between a pigtail repair connector with pre-attached lead wires ready to splice and a bare connector housing where you transfer your existing wires. OEM-spec connectors maintain the resistance and shielding required for SRS circuits.

OEM-spec pigtail connector
Best for
Fastest, most reliable repair with no guesswork on fit
What you get
Pre-wired lead wires, correct terminal plating, and exact locking tab geometry for a factory-spec connection
Bare housing connector
Best for
Shops that prefer to transfer original terminals or re-pin wires
What you get
Replacement plastic housing only; you reuse or source your own terminals and seal the splice yourself
Position-specific kit (front impact)
Best for
Vehicles with a dedicated front bumper or frame rail crash sensor
What you get
Connector matched to the higher pin count and heavier gauge wire typical of front-zone sensors
Position-specific kit (side or curtain impact)
Best for
Vehicles with B-pillar, door, or rocker panel sensors
What you get
Smaller-body connector with the correct terminal pitch and weatherproof seal for door-cavity moisture exposure

Replacing an air bag sensor connector on a Buick Century

Moderate⏱ 1–2 hoursOBD-II scanner with SRS accessTerminal pick or connector release toolWire stripper and crimping tool or soldering ironElectrical tape or heat-shrink tubingBasic socket and trim-removal set

Begin by disconnecting the negative battery terminal and waiting the manufacturer-specified time for the SRS capacitor to fully discharge before touching any connector near an airbag or sensor. Locate the faulty connector using your scanner's fault code, release the locking tab carefully, and splice or re-pin the replacement pigtail using solder and heat-shrink or a quality crimp connector rated for low-resistance circuits. Reconnect the battery, clear SRS codes, and confirm the warning light does not return before returning the Buick Century to normal use.

Frequently asked questions

How much does it cost to replace air bag sensor connectors on a Buick Century?
Parts start at low prices for a single connector pigtail on the Buick Century. A shop will typically add one to two hours of labor to locate the faulty connector, splice or re-pin it, clear the SRS codes, and verify the system. DIY replacement keeps costs near the part price alone, but always confirm the airbag light clears before driving.
Is it safe to drive a Buick Century with an airbag warning light caused by a bad sensor connector?
No. A faulty air bag sensor connector means the SRS system cannot guarantee proper airbag deployment in a crash. The airbags may fail to fire, fire with a delay, or in rare cases deploy unexpectedly. Treat an active SRS warning light as a safety issue and repair it before regular driving resumes on your Buick Century.
Can I replace the air bag sensor connector myself on a Buick Century?
A careful DIYer can replace the connector on a Buick Century, but the SRS system requires specific precautions. Always disconnect the negative battery cable and wait at least 10–15 minutes for the backup capacitor to discharge before touching any airbag wiring. Avoid probing SRS circuits with a standard test light, as voltage spikes can trigger deployment.
Will replacing the connector fix the airbag warning light on my Buick Century?
If diagnostic codes point to a circuit fault — open circuit, low resistance, or intermittent signal — at the sensor connector, replacing it typically resolves the light after codes are cleared. If the code returns, the sensor itself or the SRS control module may also need evaluation. Always re-scan after the repair to confirm no additional faults are present.
How do I know which air bag sensor connector fits my Buick Century?
Match by sensor position (front, side, or rollover), connector terminal count, and wire gauge listed in the part description. Using your Buick Century year and trim on the AutoBuffy fitment filter narrows results to connectors confirmed to match. When in doubt, compare the terminal count and locking tab orientation of your old connector to the product images before ordering.
How long does an air bag sensor connector last on a Buick Century?
Connector lifespan varies widely. Connectors in exposed locations — front bumper rails, rocker panels, or door cavities — are vulnerable to road moisture, salt, and vibration and can degrade in as little as several years. Connectors in protected interior locations often last the life of the vehicle. Corrosion and physical damage from accidents are the most common failure causes.

More parts for your Buick Century

Camshaft Position Solenoid ConnectorEngine Cylinder Head Bolt SetBrake Master CylinderAutomatic Transmission Oil Cooler TubeDual Radiator and Condenser Fan AssemblySuspension Self-Leveling Wiring Harness ConnectorVapor Canister Purge SolenoidA/C Refrigerant Suction Hose

Air bag sensor connectors for other Buick models

Buick RainierBuick RivieraBuick LeSabreBuick Regal SportbackBuick EnvisionBuick Lucerne