Loading...

Cadillac Series 62 Alignment Shims

Cadillac Series 62 Alignment shims

Alignment shims start at low prices at AutoBuffy, where you'll find multiple options from top OE-quality brands. An alignment shim is a precisely machined wedge or flat spacer inserted at control arm, strut, or axle mounting points to correct camber, caster, or toe angles. When shims wear, corrode, or go missing after suspension work, tire wear accelerates sharply and the Cadillac Series 62 pulls or wanders.

Signs your Cadillac Series 62 needs new alignment shims

  • Uneven tire wear — feathering or excessive wear on one edge of the tread that returns shortly after a fresh alignment
  • Persistent pull to one side even after a professional alignment adjustment
  • Steering wheel sits off-center on a straight, level road
  • Camber or caster readings that are out of spec and cannot be corrected within the adjuster's range of travel
  • Visible corrosion, cracking, or deformation on the existing shims during suspension inspection
  • Clunking or subtle shifting sensation at a control arm or strut mount after hitting a pothole or curb

Which alignment shim should you buy for your Cadillac Series 62?

The right shim depends on which angle you are correcting — camber, caster, or toe — and which mounting location on the Cadillac Series 62 is out of range. Shims are sold in specific thickness increments, so confirming your current out-of-spec reading in degrees before ordering lets you select the correct wedge angle or stack thickness without guessing.

OE-spec flat shim
Best for
Restoring factory alignment after suspension component replacement
What you get
Exact original thickness to bring angles back to baseline; typically stamped steel or machined aluminum
Tapered wedge shim (camber/caster correction)
Best for
Dialing in camber or caster on vehicles with limited OE adjustment
What you get
A precision-ground wedge that adds a fixed degree of correction; available in several angle increments
Eccentric / slotted bolt shim kit
Best for
Maximum adjustability on strut-type front suspensions
What you get
Combines an oversized slot or cam bolt with shim plates to allow fine-tuning across a wider correction range
Rear axle toe shim
Best for
Correcting rear toe on solid-axle or twist-beam setups with no other adjustment provision
What you get
Flat or tapered shim placed between the axle housing flange and the frame mount to shift toe in or out

Replacing alignment shims on a Cadillac Series 62

Moderate⏱ 1–3 hours (plus alignment rack time)Floor jack and jack standsSocket and breaker bar setTorque wrenchPry bar or alignment pin for hole alignmentWire brush and penetrating oil for corroded hardware

Raise and support the Cadillac Series 62 safely, then remove the wheel and unbolt the control arm or strut mount fasteners at the shim location. Slide the old shim out, clean the mating surfaces, and install the new shim oriented correctly before snugging the fasteners. Torque all mounting hardware to the manufacturer's specification with the suspension at ride height, then take the Cadillac Series 62 to an alignment rack immediately to verify and fine-tune all angles.

Frequently asked questions

How much does it cost to replace alignment shims on a Cadillac Series 62?
Parts start at low prices for a single shim or basic kit on the Cadillac Series 62. A full set covering all four corners costs more. Add shop labor for the alignment itself — typically one to two hours on a rack — and the total job usually runs noticeably more than the parts alone.
Can I drive my Cadillac Series 62 with worn or missing alignment shims?
You can drive short distances, but it is not advisable. Without correct shims the Cadillac Series 62 runs out-of-spec alignment continuously, which chews through tires unevenly, stresses wheel bearings and ball joints, and can make the vehicle handle unpredictably under hard braking or cornering. Replace them as soon as the problem is confirmed.
Do alignment shims need to be replaced every time I do suspension work on my Cadillac Series 62?
Not automatically, but they should be inspected every time a related component is removed. Shims that are corroded, bent, or have shifted out of position should be replaced. Reusing compromised shims makes it impossible to hold a stable alignment, and a fresh alignment will drift back out of spec quickly.
How do I know which shim thickness or wedge angle my Cadillac Series 62 needs?
Start with a proper four-wheel alignment printout showing how many degrees each angle is out of spec. Each degree of camber or caster correction corresponds roughly to a specific wedge angle; shim manufacturers publish conversion charts. Match the required correction angle to the available increment closest to it, erring on the conservative side.
Are alignment shims a permanent fix or a temporary workaround for my Cadillac Series 62?
A correctly sized shim installed to factory torque specs is a permanent repair, not a patch. OE designs use shims intentionally at specific mounting points. The fix becomes temporary only if an underlying structural issue — bent control arm, damaged subframe mount — is not addressed first, causing the shim to shift or compress over time.
Will adding alignment shims on my Cadillac Series 62 affect ride quality or handling?
Corrective shims restore the geometry the suspension was designed to run, so ride quality and handling typically improve. Running excess shim thickness beyond the specified correction range, however, can alter steering feel or introduce bump-steer. Stay within the manufacturer-recommended correction range and verify with a post-install alignment to confirm all angles are within spec.

More parts for your Cadillac Series 62

HVAC Pressure Switch ConnectorEngine Oil Pressure SwitchAutomatic Transmission Oil Cooler HoseDoor Jamb SwitchAutomatic Transmission Oil CoolerAlternator ConnectorComplete StrutA/C Compressor

Alignment shims for other Cadillac models

Cadillac FleetwoodCadillac EldoradoCadillac CimarronCadillac Series 60 SpecialCadillac DTSCadillac Series 61