Loading...

Chrysler Concorde Engine Oil Cooler Hose Assemblys

Chrysler Concorde Engine oil cooler hose assemblys

Starting at low prices, AutoBuffy stocks multiple engine oil cooler hose assemblies from top OE-quality brands. This hose routes pressurized oil between the engine and the oil cooler, keeping operating temperatures in a safe range. A failed hose leaks oil externally, starves the engine of lubrication, and can cause catastrophic engine damage within minutes of oil pressure loss.

Signs your Chrysler Concorde needs a new engine oil cooler hose assembly

  • Visible oil puddle or wet streaking under the engine bay near the cooler lines or radiator tank
  • Oil pressure warning light illuminates on the dashboard, especially at idle or low speed
  • Burning oil smell from the engine compartment caused by oil dripping onto hot exhaust components
  • Unexplained drop in oil level on the dipstick between normal service intervals
  • Soft, spongy, cracked, or collapsed hose body visible during a visual inspection of the cooler lines
  • Engine running hotter than normal when oil cooling capacity is reduced by a kinked or failing hose

Which engine oil cooler hose assembly should you buy for your Chrysler Concorde?

The most important decision is whether to buy an OE-equivalent assembly or an upgraded reinforced unit, and whether you need the full assembly or just the individual hose. Many assemblies are sold as a complete kit with fittings and clamps already attached, which simplifies installation and reduces the chance of fitting leaks.

OE-Replacement Assembly
Best for
Daily drivers and stock engines needing a direct, no-modification swap
What you get
Hose, pre-attached fittings, and clamps matched to factory routing and connection type
Reinforced Braided Assembly
Best for
Towing, high-load use, or engines that run consistently high oil temps
What you get
Stainless-braided outer sleeve over a synthetic inner liner for added burst strength and heat resistance
Upper Cooler Hose Only
Best for
Vehicles where only one hose has failed and the other is still in good condition
What you get
Single hose with fittings; lower cost but requires careful inspection of the mating hose before reuse
Lower Cooler Hose Only
Best for
Lower hose failure common on vehicles where the bottom line contacts heat or chassis flex points
What you get
Single hose sized and routed for the lower cooler port; often includes updated clamp hardware

Replacing the engine oil cooler hose assembly on a Chrysler Concorde

Moderate⏱ 1–2 hoursDrain pan to catch residual oilHose clamp pliers or screwdriver for spring and screw clampsCombination wrench or crow's foot set for threaded fittingsShop rags and brake cleaner for cleanupFresh engine oil for topping off after the repair

Begin by allowing the engine to cool completely, then place a drain pan under the cooler lines and loosen the clamps or fittings at both ends of the old assembly to drain residual oil. Route the new assembly along the same path as the original, ensuring it clears hot exhaust surfaces and moving components before securing all fittings and clamps. After installation, refill the engine oil to the correct level, start the engine, and inspect every connection for leaks before returning the Chrysler Concorde to service.

Frequently asked questions

How much does it cost to replace engine oil cooler hose assemblies on a Chrysler Concorde?
Parts start at low prices at AutoBuffy. A DIY replacement keeps cost to just the part and a quart of fresh oil to top off after the job. Shop labor typically adds one to two hours of labor time on top of the part cost, so doing it yourself offers meaningful savings on the Chrysler Concorde.
Can I drive my Chrysler Concorde with a leaking oil cooler hose assembly?
No. Even a slow leak steadily drops oil pressure and oil level. Low oil pressure causes metal-to-metal contact inside the engine within a short period of driving. Pull over safely, check the oil level immediately, and have the Chrysler Concorde towed or repaired before driving it again.
How long does an engine oil cooler hose assembly last on a Chrysler Concorde?
Most rubber oil cooler hoses last somewhere between 60,000 and 100,000 miles under normal conditions, but heat cycling, ozone exposure, and contact with other fluids accelerate degradation. On a Chrysler Concorde used for towing or driven in extreme climates, inspect hoses more frequently and replace them at the first sign of cracking or softness.
Is the engine oil cooler hose assembly the same as the transmission or power steering cooler hose on a Chrysler Concorde?
No. Engine oil cooler hoses carry engine oil specifically and are routed between the engine block or oil filter housing and a dedicated oil cooler or an oil-to-coolant heat exchanger. Transmission and power steering cooler hoses carry different fluids at different pressures and are not interchangeable with oil cooler hose assemblies.
Do I need to flush the oil cooler when replacing the hose assembly on my Chrysler Concorde?
It is good practice. If the old hose deteriorated internally, rubber particles or debris can contaminate the cooler passages and circulate through the engine. Flushing the cooler and performing an oil and filter change after replacing the hose assembly on the Chrysler Concorde ensures the system is clean before returning it to service.
Will a universal hose work, or do I need a vehicle-specific oil cooler hose assembly for my Chrysler Concorde?
A vehicle-specific assembly is strongly preferred. OE-fit assemblies match the exact hose diameter, length, bend geometry, and fitting type for the Chrysler Concorde, ensuring a leak-free seal without modification. Universal hoses require custom cutting, fitting selection, and clamp installation, and improper sizing raises the risk of leaks at high oil pressure.

More parts for your Chrysler Concorde

HVAC Harness ConnectorRadiator CapFuel Injection Pressure RegulatorAccessory Drive BeltAutomatic Transmission Oil Cooler TubeHVAC Control Relay ConnectorBrake Hydraulic HoseRack & Pinion Mount Bushing

Engine oil cooler hose assemblys for other Chrysler models

Chrysler LHSChrysler 300M