Loading...

Chrysler Concorde Idle Air Control Valve Connectors

Chrysler Concorde Idle air control valve connectors

Starting at low prices, AutoBuffy stocks multiple idle air control valve connectors from top OE-quality brands for the Chrysler Concorde. This connector delivers the electrical signal that tells the IAC valve how much air to bypass the throttle at idle. A cracked, corroded, or broken connector interrupts that signal, causing rough or unstable idle, stalling, and hard starts.

Signs your Chrysler Concorde needs a new idle air control valve connector

  • Rough or hunting idle — engine RPM surges up and down rather than holding steady
  • Engine stalls at stops or immediately after cold start when the IAC signal is lost entirely
  • Hard starting, especially in cold weather when the IAC is relied on most heavily
  • Idle speed is too high or too low and does not respond to load changes such as A/C or headlights switching on
  • Check Engine light with codes P0505, P0506, or P0507 pointing to IAC circuit malfunction
  • Intermittent symptoms that worsen with vibration or heat, a classic sign of a failing connector with broken or corroded pins

Which idle air control valve connector should you buy for your Chrysler Concorde?

The main decision is whether you need an OE-style direct-fit pigtail, a universal repair connector, or a weatherproof upgrade. Fit and pin count must match your existing harness exactly — a wrong pin count will not seat or will mis-wire the circuit. Check whether your Chrysler Concorde uses a 2-pin, 3-pin, or 4-pin IAC connector before ordering.

OE-spec direct-fit pigtail
Best for
Fastest, cleanest repair with no splicing
What you get
Pre-terminated leads matched to factory pin count, correct locking tab, and OE-grade terminals
Universal repair pigtail (matching pin count)
Best for
Budget repair when an exact-fit pigtail is unavailable
What you get
Bare leads you splice into the existing harness; requires heat-shrink solder connectors or crimp terminals
Weatherproof sealed connector
Best for
Vehicles in high-moisture or off-road environments
What you get
Silicone-sealed housing and tinned terminals that resist corrosion better than a standard OE-style housing
Full harness repair section
Best for
Damage extending beyond the connector body into the wiring loom
What you get
Longer lead length to reach back past burnt or chafed wire, eliminating the need for multiple splices

Replacing an idle air control valve connector on a Chrysler Concorde

Easy⏱ 30–60 minutesMultimeterWire stripper and crimping toolSolder-shrink connectors or heat gunFlathead screwdriver or terminal pickElectrical contact cleaner

Disconnect the battery negative terminal before starting, then unplug the old connector from the IAC valve and use a terminal pick to release any damaged pins from the housing. Splice the new pigtail to the existing harness wires using solder-shrink connectors, matching wire colors and maintaining correct pin positions. Reconnect the battery, clear any stored codes, and let the engine idle to confirm smooth, stable RPM.

Frequently asked questions

How much does it cost to replace idle air control valve connectors on a Chrysler Concorde?
The connector itself starts at low prices at AutoBuffy. Total repair cost depends on whether you replace only the connector or the IAC valve as well. A DIY connector swap is a low-cost fix; a shop typically charges one hour of labor on top of parts, so addressing it yourself saves the most money.
Can a bad IAC valve connector cause my Chrysler Concorde to stall?
Yes. The IAC valve relies entirely on a clean electrical signal from this connector to regulate bypass airflow at idle. A corroded or broken connector cuts or interrupts that signal, and the engine receives no idle-air correction. The result is a stall, particularly at stops or immediately after a cold start when idle-air demand is highest.
How do I know if the connector is bad versus the IAC valve itself on my Chrysler Concorde?
Unplug the connector and inspect the terminals for corrosion, spread pins, or melted plastic. Use a multimeter to verify you have battery voltage at the harness side and continuity through the connector pins. If voltage drops across the connector or a pin is damaged, the connector is the fault — not the valve itself.
Is replacing an idle air control valve connector on a Chrysler Concorde a DIY job?
For most people, yes. The connector is accessible near the throttle body and the repair requires only basic hand tools and a multimeter. A direct-fit pigtail makes it especially straightforward — cut the old connector, strip the leads, and use solder-shrink connectors to attach the new pigtail. The job typically takes under an hour.
Will a faulty IAC valve connector trigger a Check Engine light on my Chrysler Concorde?
It often does. The ECU monitors IAC circuit voltage and expected idle RPM. A damaged or corroded connector disrupts both, commonly setting codes P0505 (IAC system malfunction), P0506 (idle speed low), or P0507 (idle speed high). Clearing the code after connector replacement confirms whether the connector was the root cause.
How do I choose the right connector for my Chrysler Concorde if I'm not sure of the pin count?
Count the terminals in your existing connector or look up the IAC valve part number for your Chrysler Concorde to confirm the pin count. Most applications use a 2-pin or 3-pin connector, but some use 4 pins. AutoBuffy lists compatible vehicles on each product page, and our fit guide lets you filter by all model years and model to find the exact match.

More parts for your Chrysler Concorde

HVAC Harness ConnectorRadiator CapFuel Injection Pressure RegulatorAccessory Drive BeltAutomatic Transmission Oil Cooler TubeHVAC Control Relay ConnectorBrake Hydraulic HoseRack & Pinion Mount Bushing

Idle air control valve connectors for other Chrysler models

Chrysler PacificaChrysler LaserChrysler 300Chrysler NeonChrysler StratusChrysler Aspen