Loading...

Chrysler Daytona Vapor Canister Purge Switch Connectors

Chrysler Daytona Vapor canister purge switch connectors

Starting at $69.95, AutoBuffy stocks 1 vapor canister purge switch connectors from Standard Ignition. This connector links the purge solenoid valve to the engine wiring harness, allowing the ECU to control fuel vapor flow from the charcoal canister into the intake. A failed connector disrupts that signal, triggering evap system faults, fuel odors, and failed emissions tests on your Chrysler Daytona.

Signs your Chrysler Daytona needs a new vapor canister purge switch connector

  • Check Engine light is on with an EVAP-related trouble code such as P0443, P0444, or P0445
  • Noticeable fuel or gasoline smell near the engine bay or around the fuel tank area
  • Rough idle or hesitation on acceleration caused by uncontrolled fuel vapor entering the intake
  • Failed state emissions or OBD-II readiness test due to an incomplete EVAP monitor
  • Poor fuel economy that develops gradually as the vapor recovery system stops functioning correctly
  • Visible cracking, melting, or corrosion on the connector body or terminals when inspected under the hood

Which vapor canister purge switch connector should you buy for your Chrysler Daytona?

The main decision is whether to match OE terminal count and wire-seal type or to purchase a universal pigtail that requires splicing. Factory-fit connectors from Standard Ignition plug straight in without splicing and are the most reliable choice for a lasting repair. If the wiring harness itself is damaged near the connector, a pre-terminated pigtail with a few inches of wire gives you the flexibility to cut and join cleanly.

OE-style direct-fit connector
Best for
Clean swap with no splicing needed
What you get
Exact terminal count, correct wire-seal profile, and plug-and-play fitment for your Chrysler Daytona
Pre-terminated pigtail connector
Best for
Repairs where the harness wire is also damaged
What you get
Several inches of attached wire for a clean splice, correct connector body and terminals included
Weatherproof sealed connector
Best for
High-heat or high-moisture engine locations
What you get
Silicone-sealed terminal cavities that resist condensation and heat cycling over time
Connector repair kit (terminals + housing)
Best for
Salvaging a partially damaged connector body
What you get
Individual terminals and housing pieces so you replace only what is broken, lowest cost option

Vapor canister purge switch connectors brands we stock for your Chrysler Daytona

Standard Ignition
1 option · from $69.95

Replacing the vapor canister purge switch connector on a Chrysler Daytona

Easy⏱ 30–60 minutesFlathead screwdriver or terminal pick toolWire stripper and crimping tool (if pigtail splicing is needed)Multimeter for pre- and post-repair voltage checksElectrical contact cleaner and dielectric greaseBasic socket set for any heat shield or bracket removal

Locate the purge solenoid on your Chrysler Daytona's intake manifold or along the evap line near the charcoal canister, then depress the locking tab and pull the old connector free. If installing a direct-fit replacement, transfer or replace terminals as needed, apply a small amount of dielectric grease to the terminals, and push the connector in until it clicks. Clear any stored EVAP codes with a scan tool and run a short drive cycle to confirm the monitor completes successfully.

Frequently asked questions

How much does it cost to replace vapor canister purge switch connectors on a Chrysler Daytona?
Parts start at $69.95 for a replacement connector at AutoBuffy. DIY labor costs nothing beyond basic tools. A shop typically charges under an hour of labor since the connector is accessible on most vehicles. Combining the part cost and shop labor, most Chrysler Daytona owners spend well under $100 total for this repair.
Can a bad purge switch connector cause my Chrysler Daytona to fail an emissions test?
Yes. A faulty connector prevents the ECU from commanding the purge solenoid, leaving the EVAP monitor incomplete or setting a fault code. Most OBD-II emissions tests will automatically fail a vehicle with an active EVAP code or an incomplete readiness monitor, regardless of how well the engine runs otherwise.
Is it safe to drive my Chrysler Daytona with a damaged vapor canister purge switch connector?
Short-term driving is unlikely to cause immediate mechanical damage, but it is not advisable. An open EVAP circuit can allow raw fuel vapors to vent to atmosphere, creating a fire and inhalation hazard. A rough idle or unexpected vacuum leak condition caused by an unseated purge valve can also affect driveability and fuel economy noticeably.
How do I know if the connector is the problem versus the purge solenoid itself on my Chrysler Daytona?
Unplug the connector and inspect the terminals for corrosion, pushed-back pins, or melted plastic. Then use a multimeter to confirm the ECU is sending the correct reference voltage to the connector pins. If voltage is present at the harness side but the solenoid still fails to actuate, the solenoid is likely at fault rather than the connector.
Will any two-pin or three-pin connector work, or does it have to be vehicle-specific?
Terminal count must match, but the connector body shape, locking tab style, wire-seal diameter, and terminal pitch also need to align with your Chrysler Daytona's harness. Using a mismatched connector risks intermittent contact, moisture intrusion, and repeated fault codes. Always verify fitment using your Chrysler Daytona's year, make, and model before purchasing.
How long does a vapor canister purge switch connector typically last?
Most connectors last the life of the vehicle under normal conditions, but heat cycling, oil contamination, and road salt accelerate failure. Connectors mounted close to the exhaust or in exposed underhood locations tend to degrade sooner. Inspecting the connector during any EVAP-related repair is good practice, especially on higher-mileage Chrysler Daytona models.

Shop vapor canister purge switch connectors by year for the Chrysler Daytona

19931992199119901989

More parts for your Chrysler Daytona

Secondary Air Injection Pump Check ValveRadiator Coolant HoseA/C CondenserMulti-Purpose RelayControl Arm BushingShock Absorber SetAlternator Brush SetOxygen Sensor Set

Vapor canister purge switch connectors for other Chrysler models

Chrysler ShadowChrysler SpiritChrysler LeBaronChrysler IntrepidChrysler StratusChrysler Town Country