Loading...

Chrysler Town Country Blind Spot Detection System Warning Sensors

Chrysler Town Country Blind spot detection system warning sensors

Starting at low prices, AutoBuffy stocks multiple blind spot detection system warning sensors from top OE-quality brands. This sensor monitors the adjacent lanes and triggers a visual or audible alert when a vehicle enters your Chrysler Town Country's blind zone. When it fails, warnings stop working entirely, leaving you without a critical collision-avoidance aid during lane changes.

Signs your Chrysler Town Country needs a new blind spot detection warning sensor

  • Blind spot warning light is permanently on or flashes randomly with no vehicle nearby
  • No alert activates when a vehicle is clearly visible in the adjacent lane during highway driving
  • BSM, BLIS, or RCTA warning icon appears in the instrument cluster and does not clear
  • Sensor malfunction message displayed after rain, car wash, or road debris impact to the rear bumper
  • Turn signal activates without triggering any blind spot alert, even with traffic present
  • Rear cross-traffic alert stops functioning alongside the blind spot warning at the same time

Which blind spot detection warning sensor should you buy for your Chrysler Town Country?

The most important decision is whether to buy an OEM-equivalent direct-fit sensor or an aftermarket unit calibrated for your Chrysler Town Country's specific radar frequency and mounting position. You also need to confirm whether the failed sensor is the left-side, right-side, or a combined rear-bumper assembly, since they are not always interchangeable.

OEM-Equivalent Direct-Fit
Best for
Owners who want plug-and-play replacement with no recalibration
What you get
Matches factory radar frequency, bracket, and connector; typically requires no dealer programming
Aftermarket Performance Grade
Best for
Cost-conscious buyers willing to verify fitment carefully
What you get
Lower price point, comparable detection range, may require dealer or scan-tool calibration after install
Left-Side Sensor (Driver)
Best for
Replacing only the failed driver-side unit
What you get
Monitors the left rear quarter; sold individually to avoid unnecessary cost
Right-Side Sensor (Passenger)
Best for
Replacing only the failed passenger-side unit
What you get
Monitors the right rear quarter; most commonly damaged by parking-lot impacts and debris strikes

Replacing a blind spot detection warning sensor on a Chrysler Town Country

Moderate⏱ 1–2 hoursOBD-II scan tool (to read and clear fault codes)Trim removal pry toolsSocket and ratchet setTorx bit setPlastic clip remover

Replacement involves removing the interior trim panel or exterior rear bumper fascia to access the sensor bracket, disconnecting the wiring harness, and unbolting the old unit before fitting the new sensor in the same orientation. Once reinstalled, clear any stored fault codes with a scan tool and confirm the system self-tests correctly on the instrument cluster. If warnings do not resume normally after clearing codes, a dealer or ADAS calibration shop can perform the full radar alignment procedure.

Frequently asked questions

How much does it cost to replace blind spot detection warning sensors on a Chrysler Town Country?
Parts start at low prices on AutoBuffy. A single sensor is the main parts cost; professional installation and post-install calibration at a dealer or alignment shop adds labor on top of that. Buying the correct direct-fit sensor reduces the chance of needing expensive reprogramming.
Can I drive my Chrysler Town Country with a faulty blind spot sensor?
You can drive, but you should not rely on the system. A failed sensor gives no warning when vehicles enter your blind zone, removing a key safety layer. Treat lane changes as if the system does not exist until the sensor is replaced and confirmed working.
Does a blind spot sensor need to be calibrated after replacement on a Chrysler Town Country?
Many OEM-equivalent direct-fit sensors are pre-calibrated and activate automatically once connected. However, some Chrysler models require a calibration procedure through a dealer scan tool or ADAS calibration equipment. Check your Chrysler Town Country's service documentation or ask AutoBuffy's fitment team before purchasing.
Why does my Chrysler Town Country's blind spot sensor malfunction after rain or a car wash?
Blind spot radar sensors sit behind the rear bumper fascia and can be affected by water intrusion, accumulated debris, or a cracked sensor housing. Consistent false errors after wet conditions point to a compromised housing seal or a mounting bracket that has shifted, both of which require sensor replacement.
How do I know which side blind spot sensor has failed on my Chrysler Town Country?
Pull stored DTCs with an OBD-II scan tool; most Chrysler systems log a specific fault code identifying the left or right radar module. The warning icon on the corresponding side mirror or a one-sided alert dropout also pinpoints which sensor has failed before you begin diagnosis.
Will a used or salvage blind spot sensor work on my Chrysler Town Country?
Used sensors from the same Chrysler and model generation can work, but they carry unknown wear history and may already be drifting out of calibration. New OEM-equivalent units from top OE-quality brands provide a warranty and consistent detection performance, making them the lower-risk choice for a safety-critical component.

More parts for your Chrysler Town Country

Window RegulatorTire Pressure Monitoring System (TPMS) Programmable SensorABS Wheel Speed Sensor ConnectorSecondary Air Injection PipeStabilizer Bar BushingSerpentine BeltFuel Tank Lock RingIgnition Condenser

Blind spot detection system warning sensors for other Chrysler models

Chrysler 300Chrysler Pacifica