Loading...

Dodge W350 Fuel Shut-Off Solenoids

Dodge W350 Fuel shut-off solenoids

Starting at $116.95, AutoBuffy stocks 1 fuel shut-off solenoids from Standard Ignition to fit your Dodge W350. This solenoid controls fuel delivery to the engine by opening and closing on an electrical signal — when it fails, the engine may crank without starting, stall unexpectedly, or refuse to shut off, leaving you stranded or facing a runaway-engine risk.

Signs your Dodge W350 needs a new fuel shut-off solenoid

  • Engine cranks normally but will not start — the solenoid is stuck closed and blocking fuel flow entirely
  • Engine continues running briefly after the key is switched off, indicating the solenoid is not closing and cutting fuel
  • Sudden stalling at idle or under load with no other fuel-system fault codes present
  • Hard starting when the engine is warm, caused by an intermittent solenoid that sticks between positions
  • Audible clicking or buzzing from the solenoid body with no corresponding engine response when the key is turned to 'on'
  • Check-engine or no-start fault codes related to fuel control circuit voltage or open/short in the solenoid wiring

Which fuel shut-off solenoid should you buy for your Dodge W350?

The right solenoid depends on whether your Dodge W350 uses a diesel injection pump, a carburetor float bowl, or a fuel injection system — each design uses a different solenoid form factor and voltage rating. Confirm the mounting thread size, connector pin count, and operating voltage (typically 12V) before ordering to avoid a return.

OEM-Equivalent Replacement
Best for
Restoring factory reliability on a daily driver
What you get
Direct plug-and-play fit, matched voltage rating, and seals sized to the original bore — no modification needed
Diesel Injection Pump Solenoid
Best for
Diesel engines with mechanical injection pumps (inline or rotary)
What you get
Threaded body designed to mount directly into the pump housing, rated for high fuel pressure and diesel compatibility
Carburetor Idle Cut-Off Solenoid
Best for
Older gasoline engines with a carburetor
What you get
Compact solenoid that seats in the carb bowl, prevents dieseling on shutdown, and is usually a simple one-wire design
Heavy-Duty / Upgraded Solenoid
Best for
High-mileage vehicles, fleet use, or engines in hot or cold extremes
What you get
Reinforced coil winding and higher-grade seals for extended service life under thermal stress or frequent cycling

Fuel shut-off solenoids brands we stock for your Dodge W350

Standard Ignition
1 option · from $116.95

Replacing a fuel shut-off solenoid on a Dodge W350

Easy⏱ 30 minutes – 1.5 hoursCombination wrench or socket setMultimeter (for pre- and post-install testing)Needle-nose pliers (for connector clips)Clean rags and a small drain panThread sealant appropriate for fuel systems

Disconnect the battery negative terminal before starting to prevent accidental engine start or solenoid activation during the job. Remove the electrical connector, unthread the old solenoid carefully — on diesel injection pumps, minimize fuel spillage and keep the area clean to prevent contamination — then thread in the new solenoid, reconnect the wiring, and verify operation by cycling the key and listening for the solenoid click before attempting a start.

Frequently asked questions

How much does it cost to replace fuel shut-off solenoids on a Dodge W350?
Parts start at $116.95 on AutoBuffy. A DIY replacement keeps costs at the part price alone. Shop labor typically adds one to two hours of labor time depending on solenoid location — diesel injection pump solenoids can take longer to access than carburetor-mounted units.
Can I drive my Dodge W350 with a bad fuel shut-off solenoid?
In most cases, no. A failed solenoid usually causes a no-start condition or sudden stalling, making the vehicle undrivable. A solenoid stuck open can also prevent the engine from shutting off, which is unsafe. Replacing it promptly is the reliable fix — there is no meaningful workaround.
How do I test a fuel shut-off solenoid on my Dodge W350?
Disconnect the solenoid connector and apply 12V directly from a battery with a jumper wire. A working solenoid will produce a firm click and the plunger will move. No click, no movement, or a reading outside the manufacturer's resistance specification on a multimeter confirms the solenoid has failed.
What causes a fuel shut-off solenoid to fail on a Dodge W350?
The most common causes are coil burnout from voltage spikes or a bad ground, corrosion at the connector pins breaking the circuit, contaminated fuel degrading the internal seals, and normal wear after many years of thermal cycling. Diesel pump solenoids are especially vulnerable to dirty or water-contaminated fuel.
Is replacing a fuel shut-off solenoid a DIY job on a Dodge W350?
Carburetor idle cut-off solenoids are among the easiest fuel-system repairs — one bolt, one wire, fifteen minutes. Diesel injection pump solenoids require more care to avoid contaminating the pump during removal, but they are still within reach for a mechanically confident DIYer with the right tools and a clean work area.
Will any fuel shut-off solenoid fit my Dodge W350, or does it need to match exactly?
It must match your specific application. Thread pitch, body diameter, plunger stroke, connector type, and coil resistance all need to correspond to your engine's fuel system. Using a solenoid with the wrong resistance can cause it to overheat and fail quickly. Always verify compatibility by year, make, model, and engine before ordering.

Shop fuel shut-off solenoids by year for the Dodge W350

19931992199119901989

More parts for your Dodge W350

Exhaust Gas Recirculation (EGR) ValvePower Steering CoolerBrake Rotor SetDistributor Ignition PickupBall JointA/C ThermostatEngine Valve Cover GasketIgnition Control Module Connector

Fuel shut-off solenoids for other Dodge models

Dodge W250Dodge D250Dodge D350Dodge Ram 3500Dodge Ram 2500