Loading...

Gmc V2500 Suburban Electronic Brake Control Indicator Light Modules

Gmc V2500 Suburban Electronic brake control indicator light modules

Starting at $118.95, AutoBuffy stocks 1 electronic brake control indicator light modules from Standard Ignition. This module monitors and controls the warning light that alerts the driver when the ABS, traction control, or stability system detects a fault. When it fails, the dash light may stay on permanently, never illuminate, or give false warnings—masking real brake system faults that can compromise safety.

Signs your Gmc V2500 Suburban needs a new electronic brake control indicator light module

  • ABS or brake warning light stays illuminated constantly even after the ignition cycles off and on
  • Warning light never comes on during the bulb-check sequence at startup, suggesting the module isn't powering the circuit
  • Dashboard shows an ABS or ESC fault code (C-series DTC) with no corresponding brake system hardware defect found
  • Traction control or stability control indicator flickers randomly at highway speed with no wheel-slip event occurring
  • Scan tool shows the module is not communicating on the CAN bus or returns a U-code network fault
  • Multiple brake-related warning lights illuminate simultaneously in a pattern inconsistent with any single sensor or actuator failure

Which electronic brake control indicator light module should you buy for your Gmc V2500 Suburban?

The main decision is whether to buy an OEM-equivalent direct-fit replacement, a remanufactured unit, or a fully programmed plug-and-play assembly. Some modules require dealer-level programming after installation; others are pre-programmed to your Gmc V2500 Suburban's platform. Confirm whether your replacement needs a VIN flash before ordering.

OEM-Equivalent New Module
Best for
Owners who want factory-spec reliability and the longest service life
What you get
Brand-new unit matched to Gmc V2500 Suburban platform specs; may require dealer programming to VIN
Remanufactured / Rebuilt Module
Best for
Budget-conscious repairs where core exchange is available
What you get
Cleaned, tested, and restored original unit; lower cost but confirm warranty length before buying
Pre-Programmed Plug-and-Play Module
Best for
DIY installers who want to avoid dealership programming fees
What you get
Module pre-flashed to Gmc V2500 Suburban specs; confirms compatibility at checkout; installs and works immediately
Combination EBCM / ABS Control Unit Assembly
Best for
Cases where the indicator module and ABS control board share one housing and both are suspect
What you get
Complete integrated unit replacing module and pump/valve control together; eliminates multiple potential failure points

Electronic brake control indicator light modules brands we stock for your Gmc V2500 Suburban

Standard Ignition
1 option · from $118.95

Replacing the electronic brake control indicator light module on a Gmc V2500 Suburban

Moderate⏱ 1–2 hoursOBD-II scan tool with bidirectional ABS capabilitySocket set and ratchetTrim panel removal toolElectrical contact cleanerJ2534 pass-through device or access to a dealer (if module requires programming)

Disconnect the battery before unplugging the module's wiring harness to avoid triggering false codes or damaging the CAN network. The module is typically mounted near or on the ABS hydraulic unit under the hood, though location varies by Gmc V2500 Suburban—consult a service diagram before disassembly. After installation, use a scan tool to clear all stored fault codes, verify module communication, and confirm all warning lights extinguish normally before returning the vehicle to service.

Frequently asked questions

How much does it cost to replace electronic brake control indicator light modules on a Gmc V2500 Suburban?
Parts start at $118.95 at AutoBuffy. A remanufactured or plug-and-play unit sits at the lower end; a new OEM-equivalent runs higher. Add one to two hours of shop labor if a technician is doing the work, plus a potential dealer programming fee if your Gmc V2500 Suburban's module requires a VIN flash to activate.
Can I drive my Gmc V2500 Suburban with the brake control indicator light module failing?
Short-distance driving may be possible, but it is not advisable. A failed module can mask genuine ABS or stability control faults, meaning those safety systems may not intervene during a hard stop or slide. Until the module is replaced and fault codes are cleared, you cannot confirm the broader brake system is functioning correctly.
Will replacing the electronic brake control indicator light module clear the ABS warning light on my Gmc V2500 Suburban?
Yes, if the module itself was the source of the fault code, replacing it and clearing codes with a scan tool should extinguish the warning light. If the light returns, additional underlying faults—such as a faulty wheel speed sensor or wiring short—are present and need separate diagnosis before the repair is complete.
Does my Gmc V2500 Suburban's replacement module need to be programmed after installation?
It depends on the design. Many modern modules store VIN and calibration data and require a dealer scan tool or J2534 pass-through device to complete programming. Pre-programmed plug-and-play units sold for your Gmc V2500 Suburban skip this step. Always verify programming requirements for your specific fitment before purchasing to avoid unexpected costs.
How do I know if the indicator light module is bad versus a wheel speed sensor or ABS pump on my Gmc V2500 Suburban?
Pull the fault codes with a bidirectional scan tool. Sensor faults typically return specific wheel-position codes (e.g., left-front wheel speed signal lost). Module faults return communication errors, internal processor codes, or a complete loss of module response on the CAN network. A module that communicates but misreports data points to the module itself, not peripheral sensors.
How long does an electronic brake control indicator light module typically last on a Gmc V2500 Suburban?
Most modules are designed to last the vehicle's lifetime under normal conditions, but failure rates increase with age, moisture intrusion, or voltage irregularities from a weak battery or charging system. Corrosion on the module's connector is a common cause of premature failure, particularly in regions with road salt exposure or high humidity.

Shop electronic brake control indicator light modules by year for the Gmc V2500 Suburban

19911990198919881987

More parts for your Gmc V2500 Suburban

Engine Cooling Fan ClutchTurn Signal FlasherABS Modulator Relay ConnectorBrake Fluid Level SensorExhaust BracketBack Up Light Switch ConnectorBrake Pad & Rotor KitShock Absorber

Electronic brake control indicator light modules for other Gmc models

Gmc Sierra 2500Gmc V2500Gmc K2500Gmc S15Gmc R1500Gmc C3500HD