Loading...

International 3700 Steering Drag Link Ends

International 3700 Steering drag link ends

Starting at low prices, AutoBuffy stocks multiple steering drag link ends from top OE-quality brands for the International 3700. The drag link end is the ball-and-socket joint connecting the drag link to the steering knuckle or tie rod, transferring steering input from the gearbox to the front wheels. A worn end introduces play into that linkage, causing wandering, shimmy, and unpredictable steering response.

Signs your International 3700 needs a new steering drag link end

  • Loose or vague steering feel — the wheel moves slightly before the front wheels respond
  • Vehicle wanders or drifts on straight, flat roads without driver input
  • Visible side-to-side slop in the drag link when a helper wiggles the steering wheel with the vehicle on a lift
  • Clunking or knocking noise from the front end when turning, hitting bumps, or changing direction
  • Front-end shimmy or steering wheel shake at highway speeds or after hitting a pothole
  • Rapid or uneven tire wear on the front axle caused by the wheels being knocked out of alignment by the loose joint

Which steering drag link end should you buy for your International 3700?

The main decision is choosing the correct side and grade of joint for your driving conditions. Drag link ends are position-specific — driver side and passenger side are not interchangeable — and construction quality determines how long the new joint holds up under load and vibration. Confirm the side and whether your International 3700 uses a greaseable or sealed joint before ordering.

OE-Replacement, Sealed
Best for
Daily drivers and street use on the International 3700
What you get
Pre-greased, maintenance-free joint that meets original factory fit and load ratings; easiest swap
OE-Replacement, Greaseable (Zerk fitting)
Best for
High-mileage or older International 3700 owners who service their own undercarriage
What you get
Greaseable joint that can be re-lubricated at each service interval, extending service life in normal conditions
Heavy-Duty / Forged
Best for
International 3700 used for towing, hauling, or rough roads
What you get
Thicker housing and higher-grade ball stud rated for increased side-load and shock forces beyond OE spec
Adjustable / Rebuild-Style
Best for
Lifted or modified International 3700 with altered steering geometry
What you get
Adjustable shank length to restore correct drag link angle after a suspension lift; requires precise measurement before installation

Replacing a steering drag link end on a International 3700

Moderate⏱ 1–2 hoursFloor jack and jack standsPickle fork or ball joint separatorBreaker bar and socket setTorque wrenchCotter pin pliers or needle-nose pliers

Remove the cotter pin and castle nut securing the drag link end stud, then use a pickle fork or separator tool to pop the tapered stud free from its bore — avoid striking the stud itself. Thread the new end onto the drag link to the same depth as the old one, seat the stud fully in the knuckle, and torque the castle nut to spec before installing a new cotter pin. Schedule a front-end alignment immediately after the repair to restore correct toe and prevent tire wear.

Frequently asked questions

How much does it cost to replace steering drag link ends on a International 3700?
Parts start at low prices on AutoBuffy for the International 3700. DIY total cost is generally just the part plus basic supplies. A shop will add one to two hours of labor on top of the part cost. Replacing both ends at once is common practice and saves a second alignment fee, since an alignment is required after any drag link work.
Can I drive my International 3700 with a worn steering drag link end?
A worn drag link end makes steering unpredictable and should be replaced promptly. The joint can separate without warning if the ball stud is badly worn, resulting in a complete loss of steering control. Short, cautious trips to a shop are acceptable, but highway driving or any situation requiring precise steering input is unsafe until the part is replaced.
How long do steering drag link ends last on a International 3700?
Service life varies widely depending on road conditions, load, and whether the joint is greaseable and maintained. On a daily-driven International 3700 on paved roads, a quality replacement end typically lasts many years. Off-road use, heavy towing, or neglected lubrication on greaseable joints can shorten that window significantly. Inspect the joint annually for play and boot condition.
Do I need an alignment after replacing a drag link end on my International 3700?
Yes, a front-end alignment is required after replacing a drag link end on the International 3700. The drag link directly controls toe angle at the front wheels. Even a small change in joint position alters steering geometry, which causes tire wear and a pulled or off-center wheel. Schedule the alignment immediately after the repair.
How do I check if my International 3700's drag link end is bad?
With the International 3700 safely raised and supported, grasp the drag link near the end joint and attempt to move it side to side and up and down while a helper holds the steering wheel still. Any detectable play or clunking in the ball socket indicates a worn joint. Also inspect the rubber boot — a torn or missing boot means the joint has lost its lubrication and likely needs replacement.
Is the drag link end the same as the tie rod end on my International 3700?
No. On the International 3700, the drag link end connects the steering drag link — which runs from the steering gearbox or pitman arm — to the steering knuckle or tie rod assembly. Tie rod ends connect the tie rods to the steering knuckles. Both are ball-and-socket joints, but they occupy different positions in the linkage and are not interchangeable parts.

More parts for your International 3700

Engine Camshaft Position Sensor KitExhaust ClampHVAC Heater CoreFuel Pressure Sensor ConnectorEngine Oil FilterHVAC Blower Motor WheelShock AbsorberExhaust Manifold

Steering drag link ends for other International models

International 4300International 4200International 4900International 4700International 4800International 4600