Loading...

International 908C Ballast Resistors

International 908C Ballast resistors

Starting at $19.95, AutoBuffy stocks 1 ballast resistors from Standard Ignition to fit the International 908C. A ballast resistor limits current to the ignition coil at running speeds, preventing coil burnout. When it fails, the coil receives unregulated voltage, causing hard starts, misfires, or a no-start condition that is often misdiagnosed as a bad coil.

Signs your International 908C needs a new ballast resistor

  • Engine starts fine with the key in the 'start' position but immediately dies when released to 'run' — the classic ballast resistor failure pattern
  • Hard hot-starts: the engine restarts easily when cold but struggles or refuses to restart after reaching operating temperature
  • Weak or intermittent spark at the plugs confirmed during a spark test, despite a coil that tests within spec
  • Visible burn marks, cracks, or a charred ceramic body on the resistor itself during a visual underhood inspection
  • Coils that repeatedly burn out in short intervals, indicating unregulated voltage is destroying them
  • Rough idle or persistent misfire that does not improve after replacing spark plugs, wires, or the ignition coil

Which ballast resistor should you buy for your International 908C?

The most important factor is resistance value: using the wrong ohm rating will either starve the coil of voltage or allow too much through, replicating the original failure. Secondary considerations are construction quality — ceramic wire-wound units handle heat far better than carbon-composition types — and whether your International 908C uses a single-resistor or dual-section unit.

OE-Replacement Ceramic Wire-Wound
Best for
Daily drivers and restored vehicles needing factory-correct operation
What you get
Matches original ohm rating and physical footprint; reliable heat dissipation; direct bolt-in fit
Dual-Section Ballast Resistor
Best for
International 908C applications with separate resistance legs for the coil and electronic ignition module
What you get
Two resistance values in one unit; eliminates the need to source two separate resistors; prevents module overload
Solid-State (Electronic) Ballast
Best for
High-output or modified ignition systems running hotter coils
What you get
No resistive element to burn out; stable voltage regulation across a wide RPM and temperature range; longer service life
Universal Wire-Wound Resistor (DIY Cut-to-Value)
Best for
Budget repairs or hard-to-find applications where an exact replacement is unavailable
What you get
Lowest cost; requires confirming correct resistance with a multimeter before installation; may need custom mounting

Ballast resistors brands we stock for your International 908C

Standard Ignition
1 option · from $19.95

Replacing the ballast resistor on a International 908C

Easy⏱ 30–60 minutesMultimeter (to verify new resistor value before installation)Flathead and Phillips screwdriversNeedle-nose pliers (for push-on spade connectors)Basic socket setWiring diagram or service manual for the International 908C

Disconnect the battery, photograph or label all wiring connections to the old resistor, then remove the mounting screws and pull the unit free. Confirm the new resistor matches the required ohm value with a multimeter before bolting it in place and reconnecting the wires in the original order. Reconnect the battery and verify the engine starts and continues running with the key in the run position before closing the hood.

Frequently asked questions

How much does it cost to replace ballast resistors on a International 908C?
Parts start at $19.95 on AutoBuffy. The ballast resistor itself is one of the least expensive ignition components you can buy. DIY installation takes under an hour with basic tools, so most owners pay only the part cost. A shop might charge one hour of labor on top of the part price.
Can a bad ballast resistor cause a no-start on a International 908C?
Yes, and it is one of the most common causes of a no-start that gets misdiagnosed. When the resistor fails open, the coil receives no voltage in the run position. The engine cranks and may even fire briefly on the start-bypass circuit, then dies immediately when the key is released to run.
How do I test a ballast resistor on a International 908C?
Disconnect the resistor and measure its resistance with a multimeter set to ohms. Compare the reading to the specification for your International 908C's ignition system — the value is typically printed on the resistor body or listed in a service manual. A reading of zero or infinite resistance means the resistor has failed and must be replaced.
Will bypassing the ballast resistor damage my International 908C's coil?
Almost certainly yes over time. The ballast resistor drops voltage to the coil during normal running to prevent heat buildup. Bypassing it feeds full system voltage continuously, which overheats the coil windings and shortens coil life significantly. It is sometimes done as a temporary roadside fix only — never as a permanent solution.
Does my International 908C even have a ballast resistor?
Ballast resistors are most common on vehicles built before the mid-1980s with points-type or early electronic ignition systems. Many later systems relocated the resistance function inside the ignition module or ECU. Check your underhood wiring diagram or service manual for the International 908C to confirm whether a discrete ballast resistor is part of the ignition circuit.
How long does a ballast resistor last on a International 908C?
A quality ceramic wire-wound ballast resistor can last the life of the vehicle under normal conditions, but heat cycling, vibration, and voltage spikes from a failing charging system accelerate wear. Units mounted close to exhaust components or in poorly ventilated areas tend to fail sooner. Inspecting it whenever you service the ignition system is good practice.

Shop ballast resistors by year for the International 908C

19691968

More parts for your International 908C

Starter SolenoidMechanical Fuel PumpAutomatic Transmission Oil CoolerNeutral Safety Switch ConnectorEngine Water PumpIgnition Lock Cylinder and SwitchRadiator Coolant HoseComplete Strut

Ballast resistors for other International models

International S122International A102International B110International 900AInternational D1200International B120