Loading...

International Sm130 Brake Hydraulic Hoses

International Sm130 Brake hydraulic hoses

Starting at $15.95, AutoBuffy stocks 2 brake hydraulic hoses from Dynamic Friction for the International Sm130. A brake hydraulic hose carries pressurized fluid between the rigid steel brake lines and the moving caliper or wheel cylinder. When a hose cracks, bulges, or collapses internally, braking force drops or becomes unpredictable — a direct safety hazard that demands immediate attention.

Signs your International Sm130 needs a new brake hydraulic hose

  • Spongy or sinking brake pedal that doesn't firm up even after bleeding the system
  • Visible cracking, swelling, or bulging on the rubber hose body near the caliper end
  • Brake fluid wetness or residue on the hose surface, fitting, or surrounding components
  • One wheel drags or pulls because a collapsed hose traps pressure against a single caliper
  • Longer-than-normal stopping distances with no change in pad or rotor condition
  • Brake warning light illuminated alongside low fluid level caused by an external hose leak

Which brake hydraulic hose should you buy for your International Sm130?

The most important decisions are position (front vs. rear, driver vs. passenger side) and construction material. OE-replacement rubber hoses restore factory feel at the lowest cost, while stainless-braided hoses reduce expansion under pressure for a firmer pedal. Confirm the correct end fittings and banjo bolt thread size before ordering.

OE-spec rubber replacement
Best for
Daily drivers seeking a direct factory swap
What you get
EPDM rubber core, correct factory length and fittings, straightforward bleeding
Stainless-braided (PTFE lined)
Best for
Performance driving or upgraded braking systems
What you get
Near-zero hose expansion, firmer pedal feel, longer service life under heat cycles
Front hose (per side)
Best for
Replacing only the failed corner without a full kit
What you get
Single hose matched to the correct front-axle routing and caliper banjo size
Full hose kit (all corners)
Best for
High-mileage vehicles or brake system rebuilds
What you get
Matched set for all four corners ensuring uniform hydraulic response and simplified future service

Brake hydraulic hoses brands we stock for your International Sm130

Dynamic Friction
2 options · from $15.95

Replacing brake hydraulic hoses on a International Sm130

Moderate⏱ 1–2 hours per hoseLine wrench (flare-nut wrench) sized to the fittingCombination wrench or socket for the banjo boltBrake line clamp or hose pinch pliers to limit fluid lossCatch bottle and clear tubing for bleedingTurkey baster or fluid transfer pump for reservoir management

Loosen the hard-line fitting at the frame bracket and the banjo bolt or threaded end at the caliper, then remove the hose and bracket clip. Install the new hose with fresh sealing washers where banjo fittings are used, snugging all connections firmly without over-tightening. Bleed the affected corner until all air is purged and the pedal is firm before returning the International Sm130 to service.

Frequently asked questions

How much does it cost to replace brake hydraulic hoses on a International Sm130?
Parts start at $15.95 for a single hose on the International Sm130. A full set of hoses costs more but is often recommended on high-mileage vehicles to avoid repeat labor. Professional installation adds shop time per corner, so replacing all hoses in one visit is the most cost-efficient approach.
Can I drive my International Sm130 with a leaking brake hose?
No — a leaking brake hydraulic hose is an immediate safety risk on the International Sm130. Fluid loss reduces hydraulic pressure, which can cause brake fade or complete loss of braking at one corner. Park the vehicle and replace the hose before driving. Even a slow seep can worsen suddenly under hard braking.
How long do brake hydraulic hoses last on a International Sm130?
Rubber brake hoses typically last anywhere from several years to well over a decade depending on climate, road salt exposure, and heat cycles. On the International Sm130, inspect hoses at every brake service. Cracking, surface checking, or any internal collapse are signs to replace regardless of age or mileage.
What causes a brake hose to collapse internally on a International Sm130?
Internal collapse happens when the rubber liner delaminates and forms a one-way flap inside the International Sm130's hose. Brake pressure can push fluid through to the caliper, but fluid cannot return, leaving the caliper partially applied. The result is a dragging brake, uneven pad wear, and a wheel that gets significantly hotter than the others.
Do I need to bleed the brakes after replacing a hose on my International Sm130?
Yes. Opening any hydraulic fitting on the International Sm130's brake circuit introduces air into the system. After installing the new hose, the affected circuit must be bled until fluid flows clear and free of bubbles. Failure to bleed properly leaves air in the line, causing a spongy pedal and reduced braking effectiveness.
Are stainless-braided hoses a direct fit on the International Sm130?
Quality stainless-braided hoses designed for the International Sm130 use the same end fittings and overall length as the factory hose, making them a direct bolt-on replacement. Verify the kit is application-specific, not a universal cut-to-length item. Correct banjo bolt thread pitch and sealing washer type are critical to prevent leaks at the fitting.

Shop brake hydraulic hoses by year for the International Sm130

19571956

More parts for your International Sm130

Drive Shaft Center Support BearingAuxiliary Engine Cooling Fan AssemblyShock Absorber SetFog Light SocketAccessory Drive BeltHeadlight Dimmer SwitchIgnition CondenserDistributor Cap

Brake hydraulic hoses for other International models

International TerraStarInternational MA1200International S1924International C1300International CF500International L153