Loading...

Mazda 5 Wheel Hub Repair Kits

Mazda 5 Wheel hub repair kits

Starting at $128.95, AutoBuffy stocks 2 wheel hub repair kits from Mevotech Original Grade and Mevotech Supreme to fit the Mazda 5. A wheel hub repair kit replaces worn bearings, seals, and hardware inside the hub assembly, restoring smooth wheel rotation and proper load transfer. When these components fail, handling deteriorates and continued driving risks wheel separation.

Signs your Mazda 5 needs a wheel hub repair kit

  • Grinding, growling, or humming noise that changes pitch with vehicle speed or when shifting weight side to side during a lane change
  • Steering wheel vibration or wobble that worsens at highway speeds and cannot be corrected by wheel balancing
  • Loose or excessive play felt when grabbing the tire at the 12 and 6 o'clock positions and rocking it back and forth
  • ABS or traction control warning light triggered by a failing wheel speed sensor ring integrated into the bearing
  • Uneven or accelerated tire wear on one side caused by improper wheel alignment resulting from hub looseness
  • Clicking or popping sound during low-speed turns that indicates a severely worn or pitted bearing race

Which wheel hub repair kit should you buy for your Mazda 5?

The most important choice is whether the kit matches your hub generation and drive configuration — front hubs on driven axles carry different bearing loads than rear hubs on non-driven axles. You also need to decide whether to rebuild the existing hub with a repair kit or replace the entire hub assembly. Kits are the economical path when the hub housing itself is undamaged.

OE-Equivalent Repair Kit
Best for
Daily drivers and budget-conscious rebuilds where the hub housing is in good condition
What you get
Bearings, seals, snap rings, and hardware matched to factory specifications and tolerances
Performance / Heavy-Duty Kit
Best for
Trucks, tow vehicles, or Mazda 5 builds subject to high loads, off-road use, or frequent trailer towing
What you get
Higher load-rated bearings, upgraded seals, and corrosion-resistant hardware for extended service life under stress
Front Hub Repair Kit (Driven Axle)
Best for
Front-wheel-drive or four-wheel-drive Mazda 5 front positions with CV axle interfaces
What you get
Bearings and seals sized for the larger radial and axial loads generated at a driven, steered hub
Rear Hub Repair Kit (Non-Driven Axle)
Best for
Mazda 5 rear positions on non-driven axles where the hub spins freely without a CV shaft
What you get
Smaller-profile bearings and seals suited to lighter loads, often at a lower cost than front-axle kits

Wheel hub repair kits brands we stock for your Mazda 5

Mevotech Original Grade
1 option · from $128.95
Mevotech Supreme
1 option · from $131.95

Replacing a wheel hub repair kit on a Mazda 5

Advanced2–4 hours per cornerHydraulic floor jack and jack standsBearing press or press adapter setHub puller or slide hammerTorque wrenchSnap ring pliers

Replacing a wheel hub repair kit on the Mazda 5 requires removing the wheel, brake caliper, rotor, and any CV axle hardware to access the hub. The old bearing must be pressed out of the hub housing and the new bearing pressed in to the correct depth using a bearing press — improper installation without a press risks damaging the new bearing immediately. Reassemble in reverse order, torque all fasteners to the manufacturer's specification, and perform a road test to confirm the noise and vibration are resolved.

Frequently asked questions

How much does it cost to replace wheel hub repair kits on a Mazda 5?
Parts start at $128.95 for a Mazda 5 wheel hub repair kit at AutoBuffy. DIY cost is just the kit price plus any shop supplies. Professional labor typically adds one to two hours of shop time per corner, so total out-of-pocket cost varies depending on your local labor rate and whether one or both sides need service.
Can I drive my Mazda 5 with a bad wheel bearing?
No. A failing wheel bearing should be treated as urgent. Early-stage wear produces noise and vibration, but a severely worn bearing can seize or allow the wheel to develop dangerous play. Continued driving risks loss of vehicle control and, in extreme cases, wheel separation. Replace the hub repair kit as soon as symptoms appear.
Should I replace both sides when doing a wheel hub repair kit on my Mazda 5?
It is strongly recommended. Bearings on the same axle typically accumulate the same mileage and wear at similar rates. If one side has failed, the opposite side is often close behind. Replacing both during the same service window saves labor cost and prevents a repeat repair within a short timeframe.
How long do wheel hub bearings last on a Mazda 5?
Wheel hub bearings generally last anywhere from 75,000 to 150,000 miles under normal driving conditions, but lifespan varies widely. Frequent driving on rough or unpaved roads, exposure to road salt, aggressive cornering, and overloading all accelerate wear. Regular inspection during tire rotations helps catch early bearing deterioration before a full failure occurs.
Will a wheel hub repair kit fix my Mazda 5's ABS warning light?
It can. Many modern hub assemblies integrate the ABS wheel speed sensor tone ring into the bearing itself. When that bearing wears or corrodes, the tone ring signal becomes erratic and triggers the ABS or traction control light. Installing a new hub repair kit with a fresh integrated tone ring often resolves the fault code.
Is a wheel hub repair kit the same as a complete hub assembly for a Mazda 5?
No. A repair kit contains the internal components — bearings, seals, and hardware — needed to rebuild an existing hub housing. A complete hub assembly is a ready-to-install unit that includes the housing. Repair kits cost less but require disassembly and pressing equipment. Complete assemblies are faster to install but carry a higher parts cost.

Shop wheel hub repair kits by year for the Mazda 5

More parts for your Mazda 5

Wheel hub repair kits for other Mazda models