Loading...

Mitsubishi 3000Gt Clutch Starter Safety Switchs

Mitsubishi 3000Gt Clutch starter safety switchs

Starting at $18.95, AutoBuffy stocks 1 clutch starter safety switches from Standard Ignition. This switch prevents the engine from cranking unless the clutch pedal is fully depressed, protecting against accidental startup in gear. When it fails, your Mitsubishi 3000Gt may refuse to crank at all or start without the clutch pressed — both serious safety concerns.

Signs your Mitsubishi 3000Gt needs a new clutch starter safety switch

  • Engine won't crank at all when the clutch pedal is fully depressed — no click, no starter engagement
  • Engine cranks and starts without the clutch pedal depressed, bypassing the safety lockout entirely
  • Starter engages only when the pedal is held at a specific inconsistent point in its travel
  • Intermittent no-start condition that clears on its own, especially after jostling or adjusting the pedal
  • Starter continues to spin briefly after the key is released or after the engine fires
  • Clicking or buzzing from the starter relay with no crank, while battery and starter test healthy

Which clutch starter safety switch should you buy for your Mitsubishi 3000Gt?

Most Mitsubishi 3000Gt owners have two main decisions: OE-equivalent replacement or an adjustable aftermarket unit, and whether the switch mounts at the top of the pedal arm or lower on the bracket. Match the mounting position and connector type to your original switch before ordering, as swapping positions requires wiring changes.

OE-Equivalent Direct Fit
Best for
Straightforward like-for-like replacement with no adjustments needed
What you get
Matches original mounting point, connector, and actuation depth; plug-and-play installation
Adjustable Aftermarket Switch
Best for
Vehicles where the original switch position has shifted or pedal freeplay has changed
What you get
Threaded body lets you dial in exact actuation point; slightly more installation time required
Heavy-Duty / High-Cycle Switch
Best for
High-mileage vehicles or those used in frequent stop-and-go or fleet applications
What you get
Rated for a higher number of open/close cycles; more robust internal contacts resist wear and corrosion
Universal / Splice-In Switch
Best for
Custom builds, modified pedal assemblies, or when the OE connector is damaged
What you get
Generic body with bare-wire leads; requires splicing but fits non-standard bracket locations

Clutch starter safety switchs brands we stock for your Mitsubishi 3000Gt

Standard Ignition
1 option · from $18.95

Replacing the clutch starter safety switch on a Mitsubishi 3000Gt

Easy⏱ 15–45 minutesTest light or multimeterFlathead and Phillips screwdriversSmall open-end or combination wrench setTrim panel removal tool (if lower dash panel must come off)

Disconnect the battery negative cable first, then remove any lower dash or kick-panel trim blocking access to the clutch pedal bracket. Unplug the switch connector, unscrew or unclip the switch from its mount, and install the new unit — if it is adjustable, set actuation so the switch closes within the last quarter of full pedal travel. Reconnect the battery, verify the engine cranks only with the clutch depressed, and confirm it does not crank without it.

Frequently asked questions

How much does it cost to replace clutch starter safety switches on a Mitsubishi 3000Gt?
Parts start at $18.95 at AutoBuffy. The switch itself is inexpensive, and most shops charge less than one hour of labor since access is straightforward. Total out-of-pocket cost is typically low, making this one of the more affordable electrical repairs on a manual-transmission Mitsubishi 3000Gt.
Can I bypass the clutch starter safety switch on my Mitsubishi 3000Gt?
You can bypass it temporarily by jumping the two connector terminals, but it is not recommended as a permanent fix. Bypassing removes the only lockout preventing the engine from starting in gear, which can cause the vehicle to lurch forward and cause injury or property damage. Replace the switch instead.
How do I know if the clutch starter safety switch is bad or if it's the starter or battery on my Mitsubishi 3000Gt?
With the clutch pedal fully depressed, use a test light or multimeter at the switch connector to check for continuity when the pedal is pressed. If the switch shows no continuity at full pedal travel but the battery and starter test good, the switch is the fault. This test takes under five minutes.
Where is the clutch starter safety switch located on a Mitsubishi 3000Gt?
On most Mitsubishi 3000Gt applications the switch sits at the top of the clutch pedal arm, mounted to the bracket above the pedal pivot. It contacts a tab or plunger on the pedal when fully depressed. Some models mount it lower on the pedal shaft — check your specific bracket before ordering to confirm position.
How long does a clutch starter safety switch last on a Mitsubishi 3000Gt?
Switch lifespan depends almost entirely on cycle count — every engine start is one cycle. On a daily-driven Mitsubishi 3000Gt with normal use, these switches commonly last many years, but high-mileage vehicles, those used in frequent short trips, or switches exposed to moisture and corrosion can fail well before that general range.
Will a bad clutch starter safety switch throw a check engine light on my Mitsubishi 3000Gt?
Usually not. The clutch starter safety switch is part of the starter circuit, not the engine management system, so most Mitsubishi 3000Gt applications will not store a diagnostic trouble code when it fails. Diagnosis is done through circuit testing at the switch connector rather than scanning for fault codes.

Shop clutch starter safety switchs by year for the Mitsubishi 3000Gt

1999

More parts for your Mitsubishi 3000Gt

Oxygen Sensor SetStrut MountEngine Timing IdlerCatalytic ConverterEngine Intake ValveBrake CaliperEngine Timing Belt Idler PulleyAccessory Drive Belt Pulley

Clutch starter safety switchs for other Mitsubishi models

Mitsubishi RaiderMitsubishi EclipseMitsubishi MirageMitsubishi LancerMitsubishi PrecisMitsubishi Montero Sport