Loading...

Mitsubishi Asx Wheel Bearing Retaining Rings

Mitsubishi Asx Wheel bearing retaining rings

Starting at $7.95, AutoBuffy stocks 2 wheel bearing retaining rings from SKF and ACDelco. This small snap ring or circlip locks the wheel bearing into its hub or knuckle bore, preventing axial movement. When it fails, corrodes, or distorts, the bearing can shift under load, causing noise, play, and accelerated bearing wear that puts the wheel at risk.

Signs your Mitsubishi Asx needs a new wheel bearing retaining ring

  • Grinding or humming noise from a wheel that persists or worsens after a fresh bearing installation — the bearing is migrating axially inside the bore
  • Visible side-to-side wheel play when the wheel is grabbed at 3 and 9 o'clock with the vehicle lifted, indicating the bearing is not fully secured
  • A newly installed wheel bearing that feels loose or rotates with slight wobble during a hand-spin check before the wheel is mounted
  • Retaining ring found bent, cracked, or sitting proud of its groove during disassembly — a clear sign it failed to seat correctly or fatigued in service
  • Rapid repeat bearing failure on the same corner with no other obvious cause, often because a distorted ring never held the bearing firmly in the first place
  • Clicking or popping sound on turns that resembles a CV joint but persists even after the axle is confirmed good, caused by micro-movement of the bearing in its bore

Which wheel bearing retaining ring should you buy for your Mitsubishi Asx?

Retaining rings for wheel bearings differ by design (external circlip vs. internal snap ring vs. threaded lock ring), by diameter and thickness to match the specific hub or knuckle bore, and by material grade. Buying the correct ring means matching those dimensions precisely — an undersized or softer ring will not hold bearing preload under cornering and braking forces.

OEM-spec replacement circlip
Best for
Restoring factory fit and holding force exactly as engineered
What you get
Correct diameter, groove width, and spring-steel temper to match original specs for the Mitsubishi Asx
Heavy-duty / thicker-gauge snap ring
Best for
High-mileage vehicles, towing use, or corners with a history of repeat bearing failure
What you get
Increased radial stiffness that resists distortion under higher axial loads; may require groove inspection before fitting
Full bearing kit (bearing + retaining ring included)
Best for
Complete hub rebuild where the old ring is corroded, deformed, or unknown-grade
What you get
Matched components from one supplier; eliminates the risk of a mismatched ring paired with a new bearing
Threaded lock ring / spindle nut retainer
Best for
Front hubs that use a threaded retaining design rather than a circlip groove
What you get
Thread-engaging steel collar that replaces the snap ring function; critical to use the correct thread pitch for the Mitsubishi Asx spindle

Wheel bearing retaining rings brands we stock for your Mitsubishi Asx

SKF
1 option · from $11.95
ACDelco
1 option · from $7.95

Replacing a wheel bearing retaining ring on a Mitsubishi Asx

Moderate⏱ 1–3 hours (varies by whether a press-fit bearing is also being replaced)Internal or external snap-ring pliers (correct jaw type for your ring design)Hydraulic press or bearing separator (if the bearing must also be removed)Breaker bar and socket setPry bar or pick tool for initial ring removalTorque wrench for hub nut and caliper bolts

After the wheel, brake components, and hub or knuckle are accessible, use the appropriate snap-ring pliers to expand or compress the retaining ring and lift it free of its groove. Inspect the groove for corrosion or deformation before installing the new ring — the ring must click fully flush into the groove with no gap. Reassemble all components and verify there is no wheel play before returning the Mitsubishi Asx to the ground.

Frequently asked questions

How much does it cost to replace wheel bearing retaining rings on a Mitsubishi Asx?
The retaining ring itself starts at $7.95 for the Mitsubishi Asx. Labor is usually bundled into a full wheel bearing job, which runs roughly one to two hours at a shop. If you are already replacing the bearing, adding the ring costs very little extra and is strongly recommended to avoid a repeat failure.
Do I need to replace the retaining ring every time I replace a wheel bearing on a Mitsubishi Asx?
Yes, in most cases. A retaining ring that has been compressed, removed, and reinstalled once may not snap into its groove with full clamping force. Rings are inexpensive relative to the bearing itself, and reusing a fatigued or slightly distorted ring is one of the most common causes of premature bearing failure on the Mitsubishi Asx.
Can a bad retaining ring cause a wheel bearing to fail quickly on a Mitsubishi Asx?
Absolutely. If the ring does not seat fully, the bearing is free to move axially under load. That micro-movement generates heat, disrupts the internal race geometry, and can destroy a new bearing within a few thousand miles on the Mitsubishi Asx. Always confirm the ring is fully seated in its groove before reassembly.
How do I know what size retaining ring fits my Mitsubishi Asx?
The correct ring is determined by the hub or steering knuckle bore diameter, groove depth, and ring thickness specified for the Mitsubishi Asx. Use your vehicle's year, make, model, and drivetrain position when searching. Mixing up front and rear, or driver and passenger side, can result in a ring that is too small or too large to seat properly.
Is replacing a wheel bearing retaining ring something I can do at home on my Mitsubishi Asx?
The ring itself is straightforward to install with snap-ring pliers, but accessing it requires removing the wheel, brake caliper, rotor, and often pressing the bearing out of the knuckle. If your Mitsubishi Asx requires a hydraulic press for the bearing, the retaining ring step falls within that same job, making it moderate-to-advanced for most DIYers.
What happens if I drive my Mitsubishi Asx with a missing or broken wheel bearing retaining ring?
Without the ring, the bearing has no axial restraint and can walk out of the bore under braking or cornering forces. In a worst case this leads to complete bearing collapse, loss of steering control, or wheel separation. Even partial movement will destroy the bearing rapidly. This is a safety issue that should not be deferred on the Mitsubishi Asx.

Shop wheel bearing retaining rings by year for the Mitsubishi Asx

20142013

More parts for your Mitsubishi Asx

Auxiliary Engine Cooling Fan AssemblyAutomatic Transmission Oil CoolerTailgate Lift SupportPower Steering CoolerAir Charge Temperature Sensor ConnectorBrake RotorIgnition Knock (Detonation) SensorA/C Expansion Valve

Wheel bearing retaining rings for other Mitsubishi models

Mitsubishi MirageMitsubishi Outlander SportMitsubishi LancerMitsubishi OutlanderMitsubishi Mirage G4Mitsubishi RVR