Loading...

Mitsubishi Eclipse Strut Bellowss

Mitsubishi Eclipse Strut bellows

Strut bellows for your Mitsubishi Eclipse start at $11.95, and AutoBuffy stocks 9 options from DEA, KYB, and Dorman. The bellows is a pleated rubber or polyurethane boot that shields the strut shaft from road grit, moisture, and debris. When it tears or collapses, contamination accelerates shaft wear and can destroy an otherwise serviceable strut assembly.

Signs your Mitsubishi Eclipse needs new strut bellows

  • Visible cracks, splits, or missing sections on the accordion-style boot around the front or rear strut shaft
  • Gritty grinding sensation through the steering wheel or floorboard that worsens on rough pavement
  • Strut shaft shows scoring, rust, or a dirty ring where the seal contacts it — usually visible when the wheel is turned full lock
  • Clunking or popping noise from the suspension corner when pulling out of a parking space or navigating slow, uneven surfaces
  • Premature strut seal failure or fluid leaks shortly after replacing struts — a missing bellow lets debris cut the new seal
  • Torn or accordion-collapsed boot discovered during a tire rotation or brake inspection

Which strut bellows should you buy for your Mitsubishi Eclipse?

Strut bellows are sold individually or as part of a boot-and-bump-stop kit, and the material — rubber versus polyurethane — determines durability and price. Confirm whether you need front, rear, or all four positions before ordering, because length, diameter, and accordion depth vary by location and strut design.

OE-replacement rubber boot (single)
Best for
Restoring one torn bellow to factory spec at the lowest cost
What you get
Direct-fit EPDM rubber boot matched to original dimensions; includes clamps in most kits
Boot + bump stop kit
Best for
Complete protection when the foam bump stop is also degraded or compressed
What you get
Matched bellow and polyurethane or foam bump stop in one box; eliminates a second order
Polyurethane bellow
Best for
High-mileage or performance use where longer service life justifies higher cost
What you get
Greater abrasion and ozone resistance than standard rubber; retains shape in extreme heat and cold
Full strut assembly with bellow included
Best for
High-mileage struts where the shaft, seal, or cartridge is already worn
What you get
Complete loaded or bare strut with bellow pre-installed; saves labor if the strut itself is due for replacement

Strut bellows brands we stock for your Mitsubishi Eclipse

DEA
3 options · from $14.95
KYB
3 options · from $18.95
Dorman
2 options · from $16.95
SKP
1 option · from $11.95

Replacing strut bellows on a Mitsubishi Eclipse

Advanced1.5–3 hours per axleCoil spring compressor (rented or owned)Socket set and breaker barStrut holding tool or viseNeedle-nose pliers for bellow clampsTorque wrench

The strut assembly must be removed from the vehicle and the coil spring carefully compressed and separated before the old bellow can be slid off the shaft and the new one seated. Reinstall the bump stop inside the new bellow, confirm the bellow clamps or retaining rings are fully secured, then rebuild and reinstall the strut in reverse order. Because spring compression stores significant energy, this job is best handled by someone with prior suspension experience or a professional shop if the correct compressor is not available.

Frequently asked questions

How much does it cost to replace strut bellows on a Mitsubishi Eclipse?
Parts start at $11.95 for a single bellow kit on AutoBuffy. Because the strut must be partially disassembled to swap the boot, most independent shops bill one to two hours of labor per corner. Doing both front bellows at once is the most cost-efficient approach since the labor overlap is significant.
Can I drive my Mitsubishi Eclipse with a torn strut bellow?
You can drive short-term, but every mile without the bellow drives grit directly into the strut shaft and seal. Within weeks to months, that contamination can score the shaft and destroy the seal, turning a minor boot replacement into a full strut replacement. Fixing a torn bellow promptly is consistently the cheaper path.
Do strut bellows need to be replaced in pairs on a Mitsubishi Eclipse?
It is not required, but replacing both boots on the same axle at the same time is practical. If one bellow has failed, the other is likely the same age and material condition. Matching them prevents a second disassembly job shortly after and keeps suspension wear even side to side.
How long do strut bellows last on a Mitsubishi Eclipse?
Rubber strut bellows typically last several years under normal conditions, but lifespan shortens significantly in climates with road salt, extreme UV exposure, or unpaved surfaces. Inspecting them during every tire rotation gives the earliest warning of cracking before the bellow separates entirely and exposes the strut shaft.
Are strut bellows the same as strut boots or dust boots on a Mitsubishi Eclipse?
Yes — strut bellows, strut boots, dust boots, and dust covers all refer to the same accordion-shaped protective sleeve that wraps the exposed portion of the strut shaft. The terms are interchangeable in parts catalogs, so searching any of them for your Mitsubishi Eclipse should return the same compatible components.
Do I need a spring compressor to replace strut bellows on a Mitsubishi Eclipse?
In most cases, yes. Accessing the strut shaft requires removing the coil spring to slide the old bellow off and install the new one, which makes a spring compressor necessary for safe disassembly. Some mechanics replace the bellow as part of a full strut rebuild precisely because the spring must come off either way.

Shop strut bellows by year for the Mitsubishi Eclipse

More parts for your Mitsubishi Eclipse

Strut bellows for other Mitsubishi models