Loading...

Plymouth Breeze Ignition Switchs

Plymouth Breeze Ignition switchs

Starting at low prices, AutoBuffy stocks multiple ignition switches from top OE-quality brands to fit your Plymouth Breeze. The ignition switch is the electrical component behind the key cylinder that sends power to the starter, fuel system, and accessories. When it fails, your Plymouth Breeze may not start, lose power mid-drive, or strand you without warning.

Signs your Plymouth Breeze needs a new ignition switch

  • Engine cranks but won't start, or starter doesn't engage at all when the key is turned to the 'Start' position
  • Vehicle starts normally but stalls shortly after, often because the switch loses contact in the 'Run' position
  • Accessories such as the radio, wipers, or dash lights cut out intermittently while driving
  • Key turns freely past normal resistance with no electrical response — no dash lights, no chime
  • Vehicle starts only after wiggling or holding the key in a specific position
  • Excessive heat or a burning smell near the steering column, indicating a failing switch drawing excess current

Which ignition switch should you buy for your Plymouth Breeze?

Ignition switches are sold as the electrical switch only, or bundled with the lock cylinder. Before ordering, confirm whether your problem is electrical (the switch) or mechanical (the cylinder), since they are separate components on most Plymouth Breeze applications. Also verify whether your Plymouth Breeze requires a switch with a specific number of positions or integrated anti-theft/passlock contacts.

OE-Replacement Switch (electrical only)
Best for
Vehicles where the lock cylinder and key are still good
What you get
Direct plug-and-play fit; matches original connector, position contacts, and passlock wiring exactly
Switch + Lock Cylinder Kit
Best for
Vehicles with a worn or damaged lock cylinder, or a lost/broken key
What you get
Complete assembly including matched key; eliminates need to rekey or source parts separately
Standard/Economy Grade
Best for
High-mileage vehicles or budget repairs where longevity is secondary
What you get
Meets minimum OE specs at lower cost; suitable when resale value is low
Premium / OEM-Spec Grade
Best for
Daily drivers, newer vehicles, or cases with prior switch failures
What you get
Heavier-duty contacts, better heat resistance, and longer service life under repeated use

Replacing the ignition switch on a Plymouth Breeze

Moderate⏱ 1–2 hoursScrewdrivers (flathead and Phillips)Trim panel removal toolsSocket and ratchet setElectrical tape or heat-shrink connectorsMultimeter (recommended for diagnosis)

Replacing an ignition switch on a Plymouth Breeze typically involves removing the steering column trim panels to expose the switch housing, disconnecting the electrical connector, and unbolting or unclipping the old switch before installing the new one in reverse order. Disconnect the negative battery terminal before starting to prevent accidental shorts, particularly important on vehicles with airbag wiring routed near the column. If your Plymouth Breeze has a passlock or immobilizer system, perform any required security relearn procedure after installation before attempting to start the engine.

Frequently asked questions

How much does it cost to replace ignition switches on a Plymouth Breeze?
Parts start at low prices on AutoBuffy. A shop typically charges one to two hours of labor on top of the part cost, though column-mounted switches with anti-theft wiring or airbag system proximity can push labor higher. Doing it yourself with the right tools brings total cost close to the part price alone.
Can I drive my Plymouth Breeze with a bad ignition switch?
You should not rely on a failing ignition switch for daily driving. A switch that loses contact in the Run position can cut power to the fuel pump or ignition system while the vehicle is moving, causing a sudden stall at highway speed. This is a safety risk, not just an inconvenience.
Is the ignition switch the same as the ignition lock cylinder on a Plymouth Breeze?
No, they are two separate parts. The lock cylinder is the mechanical tumbler your key physically turns. The ignition switch is the electrical component it actuates. Either can fail independently. If your key turns but nothing happens electrically, the switch is the likely culprit. If the key won't turn at all, suspect the cylinder.
Will I need to reprogram anything after replacing the ignition switch on my Plymouth Breeze?
On most Plymouth Breeze applications, swapping the electrical switch alone does not require programming. However, if your Plymouth Breeze uses a passlock, passkey, or transponder-based immobilizer system with wiring integrated into the switch, the new switch may need to be relearned by the vehicle's security module. Check your service manual or confirm with a dealer before ordering.
How long does an ignition switch last on a Plymouth Breeze?
Ignition switches typically last many years under normal use, but lifespan varies with how often the vehicle is started, the weight of items on the keyring pulling down on the switch, and exposure to heat in the steering column. Heavy keychains are a well-documented cause of premature ignition switch wear across many vehicle types.
Can a bad ignition switch drain the battery on a Plymouth Breeze?
Yes. A faulty ignition switch can fail to fully cut power to certain circuits when the key is removed, leaving accessories, the fuel pump relay, or other loads energized. This creates a parasitic draw that drains the battery overnight or within a few days, and is sometimes misdiagnosed as a battery or alternator problem.

More parts for your Plymouth Breeze

Engine Crankshaft Position Sensor ConnectorPower Steering Pressure SwitchA/C Compressor KitA/C System O-Ring and Gasket KitControl Arm KitExhaust Pipe Flange GasketEngine Timing BeltEngine Mount

Ignition switchs for other Plymouth models

Plymouth TurismoPlymouth ScampPlymouth CricketPlymouth TC3Plymouth CaravellePlymouth PB100 Van