Loading...

Pontiac G6 Stabilizer Bar Kits

Pontiac G6 Stabilizer bar kits

Starting at low prices, AutoBuffy stocks multiple stabilizer bar kits for the Pontiac G6 from trusted brands including top OE-quality brands. A stabilizer bar kit connects your suspension across both sides of an axle to reduce body roll in corners. When the bar, end links, or bushings wear out, handling becomes unpredictable and cornering feel deteriorates noticeably.

Signs your Pontiac G6 needs a new stabilizer bar kit

  • Clunking or knocking noise from the front or rear suspension when turning or hitting bumps
  • Excessive body roll or lean when cornering, even at moderate speeds
  • Loose or vague steering feel, especially during lane changes
  • Uneven tire wear on one side caused by improper lateral load distribution
  • Squeaking or creaking from the suspension during slow maneuvers such as parking lot turns
  • Visible cracking, splitting, or complete collapse of the stabilizer bar bushings on inspection

Which stabilizer bar kit should you buy for your Pontiac G6?

A stabilizer bar kit can include the bar itself, end links, bushings, or all three — know what your Pontiac G6 actually needs before ordering. If the bar is bent or cracked, replace the whole assembly; if only the rubber components have deteriorated, a bushing-and-end-link kit may be sufficient. OEM-equivalent kits restore factory handling, while performance-grade kits can reduce body roll beyond the original spec.

OEM-Equivalent Complete Kit
Best for
Drivers who want factory ride and handling restored
What you get
Replacement bar, polyurethane or rubber bushings, and end links matched to original dimensions
Bushing & End Link Kit Only
Best for
Bars that are structurally sound but have worn rubber components
What you get
New grommets, clamps, and end links without the bar — lower cost, faster install
Performance/Heavy-Duty Kit
Best for
Drivers who want reduced body roll beyond stock or who tow/haul
What you get
Larger-diameter or stiffer bar with upgraded end links rated for higher lateral loads
Front & Rear Combo Kit
Best for
High-mileage vehicles where both axles show wear simultaneously
What you get
Complete front and rear hardware in one order, often at a reduced combined price

Replacing the stabilizer bar kit on a Pontiac G6

Moderate⏱ 1–2 hoursFloor jack and jack stands or a vehicle liftSocket set and breaker barTorx or hex bit set (for end link fasteners)Penetrating oil for corroded hardwareTorque wrench

Safely raise and support the Pontiac G6, then remove the end link nuts at the bar and the strut or control arm, followed by the bushing clamp bolts to free the bar. Install the new bushings with the factory-specified orientation, attach the new end links, and snug all fasteners with the suspension at ride height before applying final torque. Bounce the vehicle after installation to settle the components, then recheck fastener tightness.

Frequently asked questions

How much does it cost to replace stabilizer bar kits on a Pontiac G6?
Parts for a Pontiac G6 stabilizer bar kit start at low prices at AutoBuffy. A full DIY replacement including end links and bushings typically runs low-to-mid range in parts cost. Adding professional labor — usually one to two shop hours — will increase the total, so confirm which components actually need replacement before purchasing.
Can I drive my Pontiac G6 with a broken stabilizer bar or bad end links?
Driving with a failed stabilizer bar kit is not recommended. The Pontiac G6 will exhibit increased body roll and reduced cornering stability, which raises the risk of loss of control, especially in emergency maneuvers. A broken end link can also contact other suspension or brake components and cause secondary damage.
How long do stabilizer bar kits last on a Pontiac G6?
The steel bar itself can last the life of the vehicle, but rubber bushings and end links typically wear out every several years or tens of thousands of miles depending on road conditions and driving style. Vehicles frequently driven on rough roads, gravel, or in regions with road salt tend to see faster deterioration of the rubber and metal hardware.
Do I need to replace the stabilizer bar end links at the same time as the bushings on my Pontiac G6?
It is strongly advisable to replace end links and bushings together. On the Pontiac G6, both components wear at similar rates and share the same labor access. Replacing only one and leaving a marginal component in place often means returning to the same job within a short period, costing more time and money overall.
Will a stiffer aftermarket stabilizer bar kit affect the ride quality of my Pontiac G6?
Yes. A larger-diameter or higher-spring-rate bar reduces body roll but transmits more lateral force through the suspension, which can make the ride feel firmer over sharp bumps. For a Pontiac G6 used primarily for daily commuting, an OEM-equivalent kit maintains the factory balance between handling and comfort.
Is replacing a stabilizer bar kit on a Pontiac G6 something I can do at home?
Bushing and end link replacement on the Pontiac G6 is considered moderate difficulty and is achievable for a home mechanic with basic tools and a safe lift or jack stands. Replacing the full bar requires more disassembly but remains within reach. Seized hardware on older vehicles is the most common complication that extends job time.

More parts for your Pontiac G6

Accelerator Pedal SensorFuel Pump Module AssemblyHVAC Pressure TransducerA/C CondenserTrailing ArmTrunk Lid Release SwitchEngine Crankcase Breather HoseEngine Timing Cover Gasket Set

Stabilizer bar kits for other Pontiac models

Pontiac AztekPontiac Trans SportPontiac SunfirePontiac BonnevillePontiac PursuitPontiac G5