Loading...

Porsche 930 Door Hinge Bushings

Porsche 930 Door hinge bushings

Door hinge bushings for your Porsche 930 start at low prices, and AutoBuffy carries multiple options from top OE-quality brands. These small nylon or metal sleeves line the hinge pin bore, letting the door pivot smoothly without metal-on-metal contact. When they wear out, the door sags, binds, and can damage the latch — making replacement a high-value, low-cost fix.

Signs your Porsche 930 needs new door hinge bushings

  • Door sags visibly when fully open, dropping below its normal level relative to the body panel
  • Door scrapes or rubs against the door jamb or rocker panel when opening or closing
  • You hear a clunking, popping, or grinding noise at the hinge point as the door swings
  • The door latch no longer aligns with the striker plate, requiring extra force or a lift to close
  • Loose, sloppy feel in the door when you grab the edge and shake it up and down
  • Visible rust streaks or metal filings accumulating below the hinge, indicating metal-on-metal wear

Which door hinge bushings should you buy for your Porsche 930?

The main decision is material and whether you replace the bushing alone or the full hinge pin-and-bushing kit. Bushing material affects durability and how well the repair holds up to daily door cycles. Match the kit to the hinge position — upper and lower hinges on a heavy door wear at different rates and sometimes use different bushing diameters.

OE-spec nylon bushing
Best for
Daily drivers and exact factory-feel restoration
What you get
Factory-matched plastic sleeve that meets original dimensions and pivot feel
Pin and bushing kit
Best for
Severely worn hinges where the pin itself is grooved or loose
What you get
Replacement hinge pin plus matched bushings sold as a paired set for a complete repair
Bronze/sintered metal bushing
Best for
High-cycle use, heavy doors, or trucks and SUVs with frequent entry/exit
What you get
Harder-wearing metal sleeve that resists deformation under heavier door loads
Upper + lower hinge set
Best for
Full door restoration or when both hinge positions show play
What you get
Complete pair of bushings (or pin-and-bushing kits) sized for both hinge mounting points

Replacing door hinge bushings on a Porsche 930

Moderate⏱ 1–2 hours per doorPunch or hinge pin removal toolHammer or malletBushing driver or socket sized to the bushing ODPry bar or door supportWhite lithium grease or grease gun

Support the door with a floor jack and wood block or an assistant before driving out the old hinge pin with a punch and hammer. Press or tap the worn bushings out of the hinge barrel, seat the new bushings flush, reinstall the pin, and apply grease to the pin and bushing bore before closing everything up. Verify door alignment and latch engagement before returning the vehicle to service.

Frequently asked questions

How much does it cost to replace door hinge bushings on a Porsche 930?
Parts start at low prices for a basic bushing set. A full pin-and-bushing kit costs more but is often the smarter buy when the pin is also worn. DIY labor is minimal. Shop labor typically runs one to two hours per door, so doing it yourself saves the most money on this repair.
Can I replace just the bushings without replacing the entire door hinge on my Porsche 930?
Yes, in most cases. If the hinge plate and pin are not cracked, bent, or severely grooved, swapping the bushings restores proper door alignment at a fraction of the cost of a full hinge replacement. Inspect the pin for deep wear grooves first — a grooved pin will quickly destroy new bushings.
How long do door hinge bushings last on a Porsche 930?
Service life varies widely based on door weight, use frequency, and climate. In typical conditions, bushings last many years, but heavy doors, frequent entry and exit cycles, and lack of lubrication accelerate wear. Bushings in rust-prone climates or on larger vehicles like trucks and SUVs tend to wear sooner than those on lighter passenger cars.
Do I need to remove the door to replace hinge bushings on a Porsche 930?
Not always, but removing the door makes the job significantly easier and safer. With the door off, you have clear access to drive out the old pin, press or tap in new bushings, and reinstall the pin without awkward angles. Some technicians complete the job with the door on a support, but door removal is the recommended approach.
Will worn hinge bushings cause my Porsche 930's door to not close properly?
Yes. As bushings wear, the door droops on its hinge pins and shifts out of alignment with the striker plate. This causes the latch to miss or bind, requiring you to lift the door while closing it. Left unaddressed, the misalignment strains the latch mechanism and can eventually damage the striker plate or door latch assembly.
Should I replace hinge bushings on both doors at the same time on my Porsche 930?
It depends on wear. Because doors on the same vehicle experience similar use, it is common for multiple doors to show bushing wear at roughly the same mileage. Inspect all door hinges when you have one apart. Replacing worn bushings across multiple doors in one session saves time and prevents a second round of the same repair shortly after.

More parts for your Porsche 930

Headlight Bucket Drain TubeSun Visor ClipSteering Column Universal Joint AssemblyControl Pedal BushingSpark PlugBrake Bleeder Screw CapShock AbsorberPower Antenna

Door hinge bushings for other Porsche models

Porsche 911Porsche 912