Bend TypeMandrel
Catalytic Converter IncludedNo
Clamp TypeU-Bolt
Clamps IncludedYes
Effective Length965 MM
Grade TypePerformance
Hangers IncludedYes
Inlet Type6 Bolt Welded
MaterialFiber Loaded Rubber
Mounting Hardware IncludedYes
Muffler Body Length18 IN
Muffler MaterialSteel
Muffler Type IncludedSuper Turbo
Outlet Type2 Bolt Welded
Over All Length15in.
Oxygen Sensor Bung IncludedNo
Packaging TypeBoxed
Pipe Diameter3 IN
Pipe MaterialSteel
System TypeSingle
Tip MaterialSteel
Angle36 Degrees
Banded BeltN
Belt ConstructionBottom Cog
Catalytic Converter Quantity0
Clamp Count2
ColorBlack
Exhaust Tip Quantity1
Exit LocationAngle
Faq - Answer 1Yes, this may be indicative of an alignment issue or a failed tensioner.
Faq - Answer 2Yes, you may lose your power steering or stall out. Your car is not drivable when your drive belt fails.
Faq - Answer 3Yes, the leading causes of belt failure are improper tension and misaligned pulleys. Both these conditions cause excessive heat which leads to belt failure. Have your belts checked every 3,000 miles f
Faq - Answer 4No, when the belt backing has been torn or cracked, the belt should be replaced.
Faq - Answer 5No, use the belt in the way it's listed in the ACDelco belts and hoses catalog.
Faq - Answer 6No, remember the leading cause of belt failure is improper tension and misaligned pulleys. Improper tension will cause the belt to slip and you may notice a loss of performance from the air conditioni
Faq - Question 1Could an automotive belt tear during use?
Faq - Question 2Will I know immediately if an automotive belt tears?
Faq - Question 3Are there steps I can take to ensure a longer automotive belt life?
Faq - Question 4Is there a way to repair a torn automotive belt?
Faq - Question 5Can I use the same automotive belt for multiple uses?
Faq - Question 6Will a worn automotive belt affect gas mileage?
Features Benefits - Bullet 1Its fiber loaded rubber stock puts more flexibility along the length of the belt, yet gives the belt greater lateral stability in the pulley
Features Benefits - Bullet 2Has thermally active tensile cords that provide maintenance free performance when properly installed and tensioned
Features Benefits - Bullet 3Manufactured with form ground to ensure precise top width and sidewall dimensional control for proper fit in the pulley as well as a smoother, quieter running belt
Good Maintenance Practices - Section 1 - Bullet 1Do not use belt dressings to stop belt slippage or noise. These are oil based and may cause belt deterioration.
Good Maintenance Practices - Section 1 - Bullet 2Never twist a belt more than 90 degrees during inspection. This may damage the tensile cords and cause premature failure.
Good Maintenance Practices - Section 1 - Bullet 3Replace serpentine belts every 60,000 - 100,000 miles. Check vehicle's owner's manual.
Good Maintenance Practices - Section 1 - Bullet 4Replace V-belts after 3 to 4 years, or every 36,000 to 48,000 miles.
Good Maintenance Practices - Section 1 - Bullet 5Use an approved tension gauge to check belt tension.
Good Maintenance Practices - Section 1 - Bullet 6Check for proper belt tension after 500 to 1,000 miles following belt installation. Recheck often, at least twice a year or every 6,000 miles.
Inlet Quantity1
Kit ContentsIntermediate Pipe, Tail Pipe, Clamps
Large Pkg. FeeNo
Maximum Operating Temperature175 F
Measurements50 1/2 in x 38 3/8
Minimum Operating Temperature-35 F
Muffler FinishAluminized
Muffler Quantity1
Number Of O2 Sensors1
Outlet Quantity1
Outside Circumference975 MM
Pipe FinishAluminized
Product DescriptionACDelco Professional, premium aftermarket V-Belts serve as replacement belts for today's most demanding engine drives. Due to thermal forces, these variable notched belts actually tighten on the drive
Signs Of Wear Troubleshooting - Section 1 - Bullet 1Rubber Loss: (most common belt wear) a belt wear gauge measures rubber loss, which can result in reduced power transfer from the crank to the accessories.
Signs Of Wear Troubleshooting - Section 1 - Bullet 2Glazing: shiny spots can indicate a slipping belt that isn't properly transferring power to accessories.
Signs Of Wear Troubleshooting - Section 1 - Bullet 3Pilling: worn rubber can fill in grooves and cause noise, heat, vibration, and excessive wear.
Signs Of Wear Troubleshooting - Section 1 - Bullet 4Abrasion: wear along the side could indicate misalignment due to a failed tensioner.
Signs Of Wear Troubleshooting - Section 1 - Bullet 5Cracking: older neoprene belts crack as they near the end of their life cycle and often need to be replaced.
Signs Of Wear Troubleshooting - Section 1 - Bullet 6Engine stops or backfires.
Signs Of Wear Troubleshooting - Section 1 - Bullet 7The belt is producing a squealing noise.
Signs Of Wear Troubleshooting - Section 1 - Bullet 8Headlights dim while driving.
Signs Of Wear Troubleshooting - Section 1 - Bullet 9Loss of battery charge.
StandardsSAE J636, SAE J637
Tip CutStraight
Tip FinishAluminized
Tip Outlet Size3
Tip ShapeRound
Top CoggedNo
Top Width0.47 IN
Use Davico Decarbonizing Induction Kit 1540EaYes
System StyleCat Back
Tip Edge StyleNon-Rolled