Loading...

Studebaker E16 Starter Solenoids

Studebaker E16 Starter solenoids

Starting at $20.95, AutoBuffy stocks 3 starter solenoids from Standard Ignition to fit the Studebaker E16. The starter solenoid is an electromagnetic switch that sends high-amperage current from the battery to the starter motor when you turn the key. When it fails, the engine won't crank — leaving you stranded.

Signs your Studebaker E16 needs a new starter solenoid

  • Single loud click when turning the key, with no engine crank following
  • Rapid clicking sounds from the engine bay but the starter motor never engages
  • Starter engages intermittently — starts fine one time, nothing the next
  • Starter motor runs continuously after the key is released or the engine starts
  • Burning smell or visible heat damage near the solenoid or starter assembly
  • Battery tests fully charged but the vehicle still won't crank or respond to the key

Which starter solenoid should you buy for your Studebaker E16?

The most important decision is whether your Studebaker E16 uses a solenoid mounted directly on the starter motor or a remote-mount solenoid on the firewall or fender well — these are not interchangeable. Beyond fitment, consider whether you want an OEM-equivalent unit for reliability or a rebuilt/economy option to control cost.

OEM-Replacement (Starter-Mounted)
Best for
Daily drivers needing exact-fit reliability
What you get
Direct bolt-on to existing starter, matches original current rating and terminal layout
Remote-Mount Solenoid
Best for
Vehicles with firewall- or fender-mounted solenoid design
What you get
Standalone unit wired between battery and starter; easier bench replacement without pulling the starter
Remanufactured Unit
Best for
Budget-conscious owners who want a tested component
What you get
Rebuilt to OEM specs, often with a limited warranty; good middle ground between new and economy
Heavy-Duty / High-Amperage Upgrade
Best for
Modified engines, high-compression builds, or frequent hard-start conditions
What you get
Higher contact rating handles increased current draw without premature contact erosion

Starter solenoids brands we stock for your Studebaker E16

Standard Ignition
3 options · from $20.95

Replacing the starter solenoid on a Studebaker E16

Easy⏱ 30 minutes – 1.5 hoursSocket set and ratchetMultimeter (for pre- and post-install testing)Wire brush or terminal cleanerScrewdrivers (flathead and Phillips)Battery terminal wrench

Always disconnect the negative battery cable before touching any solenoid terminals to prevent accidental shorting. Label or photograph each wire connection before removal, as the small trigger terminal and large battery and starter cables must return to their correct posts. After installation, reconnect the battery and test for a clean, single-engagement crank before considering the job complete.

Frequently asked questions

How much does it cost to replace starter solenoids on a Studebaker E16?
Parts start at $20.95 on AutoBuffy for a Studebaker E16 starter solenoid. A remote-mount solenoid is typically a straightforward DIY job under an hour, keeping total cost low. If the solenoid is integrated into the starter, a shop may bundle labor with a starter replacement, raising the overall bill.
Can a bad starter solenoid drain the battery on a Studebaker E16?
Yes. A shorted or stuck-closed solenoid can hold the starter circuit partially energized, causing a parasitic drain that depletes the battery overnight. If your Studebaker E16 battery keeps going dead with no obvious cause, test the solenoid for continuity when the key is off before assuming the battery or alternator is at fault.
How do I know if it's the starter solenoid or the starter motor itself that's bad on my Studebaker E16?
A single loud click points to the solenoid failing to pass current; rapid clicking often indicates low voltage, not a failed solenoid. To isolate the fault, use a multimeter to check voltage at the solenoid output terminal during cranking. Full battery voltage present but no crank confirms the starter motor is the problem, not the solenoid.
Is a starter solenoid the same as a starter relay on a Studebaker E16?
They are related but not the same. The relay is a low-current switch in the fuse box that triggers the solenoid circuit; the solenoid is the heavy-duty switch that actually connects battery power to the starter motor. Both can cause a no-crank condition when they fail, so test both before replacing parts.
How long does a starter solenoid last on a Studebaker E16?
Most starter solenoids last many years and tens of thousands of ignition cycles under normal use. Premature failure is typically caused by corrosion on terminals from moisture exposure, extended cranking that overheats the contacts, or voltage spikes from a weak or failing battery that forces the solenoid to work harder than rated.
Can I replace just the solenoid, or do I need to replace the whole starter on a Studebaker E16?
On many Studebaker E16 applications with a starter-mounted solenoid, the solenoid can be unbolted and replaced independently without buying a whole starter assembly, which saves money. However, if the starter motor itself shows signs of wear — slow cranking, grinding, or high current draw — replacing both at the same time avoids a second labor job soon after.

Shop starter solenoids by year for the Studebaker E16

19561955

More parts for your Studebaker E16

Distributor CapStarter BushingHeadlight Dimmer SwitchHorn RelayDistributor RotorVoltage RegulatorIgnition CondenserAlternator Brush Set

Starter solenoids for other Studebaker models

Studebaker 7E13Studebaker 5E12Studebaker 8E15Studebaker E28Studebaker 4E2Studebaker 7E10