Loading...

Suzuki Reno Torque Strut Mounts

Suzuki Reno Torque strut mounts

Torque strut mounts for your Suzuki Reno start at $13.95, and AutoBuffy stocks 6 options from DEA, SKP, and Westar. The torque strut mount controls engine movement under acceleration and braking, absorbing the rotational torque that would otherwise let the engine lurch forward and back. When it fails, vibration and clunking transfer directly into the cabin and can accelerate wear on surrounding drivetrain components.

Signs your Suzuki Reno needs a new torque strut mount

  • Loud clunk or thud when shifting from Park into Drive or Reverse
  • Engine visibly lurching forward under hard acceleration or snapping back when you lift off the throttle
  • Vibration felt through the floor or steering wheel that worsens at low RPM or idle
  • Rattling noise from the engine bay that changes with engine load rather than road speed
  • Visible cracking, tearing, or collapsed rubber on the mount when inspected
  • Increased harshness when engaging the clutch on manual-transmission vehicles

Which torque strut mount should you buy for your Suzuki Reno?

The main decision is between OEM-style rubber mounts and stiffer performance or polyurethane units — rubber rides quieter while poly holds the engine tighter under hard use. You should also confirm whether your Suzuki Reno uses a single torque strut or a front-and-rear pair, since replacing only one worn mount often leaves the other ready to fail within months. Westar is a specialist mount manufacturer widely regarded for strong fitment and value on engine and transmission mounts, making their rubber-replacement units a reliable everyday choice.

OEM-style rubber replacement
Best for
Daily drivers wanting factory ride quality
What you get
Quiet, vibration-absorbing mount that restores stock behavior with no NVH penalty
Hydraulic fluid-filled mount
Best for
Vehicles that originally used a hydraulic mount
What you get
Superior vibration damping at idle and low RPM; direct replacement for hydraulic OEM units
Polyurethane mount
Best for
Performance or high-mileage vehicles where tighter engine control matters
What you get
Firmer bushing that resists sagging under torque; trades some noise isolation for precision
Complete bracket-and-mount assembly
Best for
High-mileage vehicles where the bracket is corroded or damaged
What you get
New hardware and mount together; avoids misalignment from reusing a bent or cracked bracket

Torque strut mounts brands we stock for your Suzuki Reno

DEA
2 options · from $62.95
SKP
2 options · from $50.95
Westar
2 options · from $13.95

Replacing a torque strut mount on a Suzuki Reno

Moderate1–2 hoursSocket set with metric and standard socketsBreaker bar or impact wrenchFloor jack and jack stand (to support engine if needed)Pry barTorque wrench

Support the engine with a floor jack and a block of wood under the oil pan before unbolting the old mount, which prevents the engine from dropping and binding the new hardware during installation. Remove the mount-to-bracket and mount-to-engine bolts, swap in the new torque strut mount, and hand-thread all fasteners before snugging them to specification with a torque wrench. Lower the jack gradually to let the mount settle under engine weight, then confirm nothing is contacting surrounding components before returning the vehicle to service.

Frequently asked questions

How much does it cost to replace torque strut mounts on a Suzuki Reno?
Parts alone start at $13.95 for a torque strut mount for your Suzuki Reno. If you pay a shop, labor typically adds one to two hours of shop time depending on accessibility. DIY replacement is straightforward on most platforms, so doing it yourself keeps the total cost close to the part price.
What happens if I keep driving my Suzuki Reno with a bad torque strut mount?
A failed torque strut mount allows excessive engine movement that can stress CV axles, damage other mounts, and strain coolant and vacuum hoses that connect to the engine. Over time this can turn a simple mount replacement into a more expensive multi-component repair, so it is worth addressing the mount promptly once symptoms appear.
How long does a torque strut mount last on a Suzuki Reno?
Most rubber torque strut mounts last somewhere between 60,000 and 150,000 miles, though heat cycles, aggressive driving, and oil contamination from nearby leaks can shorten that range considerably. Polyurethane units generally resist deterioration longer but can transmit more vibration as the vehicle ages.
Can I replace just the torque strut mount, or do I need to replace all mounts at once?
You can replace the torque strut mount on its own, and doing so often resolves clunking immediately. However, if other mounts are original and have similar mileage, inspecting them at the same time is practical. Replacing two worn mounts together saves labor compared to doing each job separately a few months apart.
Is replacing a torque strut mount on a Suzuki Reno a job I can do at home?
For most front-wheel-drive vehicles, yes. The torque strut mount is typically bolted to the engine and to a bracket on the frame or strut tower and is accessible without removing major components. The job generally takes one to two hours with basic hand tools, though tight engine bays may require removing an airbox or battery tray first.
Will a bad torque strut mount cause my Suzuki Reno to fail an inspection?
A severely deteriorated mount that allows the engine to move far enough to contact other components or cause visible instability could draw attention during a safety inspection in some states. More commonly, though, a bad torque strut mount fails on noise and driveability grounds rather than triggering a formal inspection failure outright.

Shop torque strut mounts by year for the Suzuki Reno

More parts for your Suzuki Reno

Torque strut mounts for other Suzuki models