Loading...

Volvo 245 Ignition Coil Mounting Brackets

Volvo 245 Ignition coil mounting brackets

Starting at $8.95, AutoBuffy stocks 1 ignition coil mounting brackets from Standard Ignition. This bracket bolts the ignition coil to the engine block or valve cover, holding it in precise alignment with the spark plug. A cracked, corroded, or broken bracket lets the coil shift under vibration, causing misfires, rough idle, and potential coil failure.

Signs your Volvo 245 needs a new ignition coil mounting bracket

  • Persistent engine misfire on a specific cylinder even after replacing the coil itself
  • Ignition coil sits visibly loose, tilted, or vibrates noticeably at idle
  • Spark plug boot pops off or seats poorly because the coil is misaligned
  • Check Engine light with misfire codes that return shortly after clearing
  • Visible cracks, breaks, or stripped mounting holes on the bracket
  • Intermittent no-start or stumble that worsens over rough roads or high RPM

Which ignition coil mounting bracket should you buy for your Volvo 245?

The main decision is material and fitment precision. OE-spec brackets match the original mounting geometry exactly, which matters because even a small misalignment stresses the coil connector and boot. If the original bracket failed due to heat cycling or corrosion, an upgraded material or reinforced design is worth considering.

OEM-Equivalent (Stamped Steel)
Best for
Daily drivers, exact-fit replacement
What you get
Matches original dimensions and mounting points; bolt-in installation with no modification
OEM-Equivalent (Cast Aluminum)
Best for
Vehicles where heat-related cracking was the original failure mode
What you get
Better thermal resistance than stamped steel; lighter weight; same OE mounting pattern
Reinforced Aftermarket
Best for
High-mileage vehicles or those with repeated bracket failures
What you get
Thicker gauge or gusseted design for added rigidity; may include new hardware
Position-Specific (Bank 1 / Bank 2)
Best for
V-configuration engines with asymmetric coil layouts
What you get
Designed for a specific cylinder bank; incorrect side will not align — confirm position before ordering

Ignition coil mounting brackets brands we stock for your Volvo 245

Standard Ignition
1 option · from $8.95

Replacing the ignition coil mounting bracket on a Volvo 245

Easy⏱ 30–60 minutesSocket set with extensionsScrewdriver set (flathead and Phillips)Torque wrenchTrim removal tool or pick (for connector clips)

Disconnect the battery negative terminal, then unplug the coil electrical connector and remove the coil from the old bracket. Unbolt the damaged bracket, transfer or install the coil onto the new bracket, and torque the mounting fasteners to the manufacturer's specification for your engine. Reconnect the coil connector and battery, then clear any stored misfire codes and verify smooth idle before returning the vehicle to service.

Frequently asked questions

How much does it cost to replace ignition coil mounting brackets on a Volvo 245?
Parts start at $8.95 on AutoBuffy. Because the bracket itself is a straightforward bolt-on component, DIY labor is minimal — usually under an hour. Shop labor costs vary but are typically low since coil access is simple on most engines. Replacing the bracket early prevents costlier coil or ignition damage.
Can a bad ignition coil mounting bracket cause a misfire on a Volvo 245?
Yes. A broken or loose bracket allows the ignition coil to shift out of alignment with the spark plug, creating a poor electrical connection or intermittent contact. This produces the same misfire codes as a failed coil. If a new coil does not resolve the misfire, inspect the bracket before replacing additional parts.
Is it necessary to replace the ignition coil when replacing the mounting bracket on a Volvo 245?
Not always, but it is worth inspecting the coil carefully. If the bracket failed due to vibration or impact, the coil boot, connector, and winding may have absorbed stress. If the coil tests within spec and shows no cracking or carbon tracking, it can typically be reused with the new bracket.
How do I know which ignition coil mounting bracket fits my Volvo 245?
Fitment depends on engine type, cylinder count, and coil configuration. On V-engines, brackets are often side-specific — bank 1 and bank 2 are not interchangeable. Use your Volvo 245's VIN or engine code when searching to ensure you get the correct position and mounting-hole pattern. AutoBuffy's fitment filter narrows results automatically.
What causes ignition coil mounting brackets to fail on a Volvo 245?
The most common causes are heat cycling that embrittles plastic or corrodes steel over time, physical impact from engine vibration or road debris, and stripped mounting threads from overtightening during a previous coil replacement. Vehicles with high underhood temperatures or older, high-mileage engines see bracket failures most frequently.
Are ignition coil mounting brackets vehicle-specific or universal?
They are vehicle-specific. The bracket geometry, bolt spacing, and coil-seat angle are engineered for a particular engine family. Universal brackets do not exist for this application. Always match the bracket to your exact Volvo 245 make, model, engine displacement, and — on multi-coil engines — the specific cylinder position being serviced.

Shop ignition coil mounting brackets by year for the Volvo 245

1988198719861985

More parts for your Volvo 245

StarterA/C Refrigerant Suction HoseBattery Hold DownAccessory Power Relay ConnectorBack Up Light SwitchUniversal JointPre Heat HoseTie Rod End

Ignition coil mounting brackets for other Volvo models

Volvo 445Volvo 1800Volvo 244Volvo 122Volvo 544