Loading...

Workhorse Fastrack Ft1601 Vapor Canisters

Workhorse Fastrack Ft1601 Vapor canisters

Starting at low prices, AutoBuffy stocks multiple vapor canisters from top OE-quality brands for the Workhorse Fastrack Ft1601. The vapor canister captures fuel vapors from the gas tank and stores them until the engine can burn them off, keeping harmful hydrocarbons out of the atmosphere. A failed canister triggers a check engine light, causes failed emissions tests, and can disrupt fuel delivery.

Signs your Workhorse Fastrack Ft1601 needs a new vapor canister

  • Check engine light is on with an EVAP-related code such as P0440, P0441, P0442, or P0446
  • Strong smell of raw gasoline near the rear of the vehicle or around the fuel tank
  • Failed state emissions or smog inspection due to an EVAP system fault
  • Difficulty filling the fuel tank — the pump nozzle clicks off repeatedly as if the tank is full
  • Rough idle or hesitation on cold starts caused by vapor pressure imbalance in the fuel system
  • Purge valve cycling incorrectly or fuel trim readings that are persistently rich at idle

Which vapor canister should you buy for your Workhorse Fastrack Ft1601?

The most important decision is whether to buy an OE-equivalent replacement or a performance-grade canister with higher vapor storage capacity. You also need to confirm the canister matches the original mounting configuration and port count, since Workhorse uses different designs across model years and trim levels.

OE-Equivalent (Direct-Fit)
Best for
Most drivers doing a straightforward repair
What you get
Matches original port layout, bracket, and charcoal capacity; bolt-on installation with no modification
OEM-Sourced (Dealer-Grade)
Best for
Owners who want factory-spec materials and longest expected service life
What you get
Identical to the part the Workhorse Fastrack Ft1601 shipped with; highest confidence in fit and durability
High-Capacity Charcoal Canister
Best for
Vehicles in hot climates or with modified fuel systems that generate higher vapor loads
What you get
Larger activated-charcoal bed absorbs more vapor before saturation; reduces purge frequency
Budget/Economy Replacement
Best for
Short-term fix or low-mileage vehicles where cost is the primary concern
What you get
Meets basic OBD-II readiness requirements; may use lower-grade charcoal media with a shorter service interval

Replacing the vapor canister on a Workhorse Fastrack Ft1601

Moderate⏱ 1–2 hoursSocket set and ratchetFlathead and Phillips screwdriversTrim removal pry toolOBD-II scan tool (to clear codes and run EVAP readiness monitor)Safety glasses and nitrile gloves

Raise and support the vehicle safely if the canister is mounted under the rear, then disconnect the negative battery terminal before handling any EVAP components. Carefully label or photograph each hose and electrical connector before removal, since port orientation must match exactly on the new canister. After installation, use an OBD-II scanner to clear the fault code and run an EVAP monitor drive cycle to confirm the system is operating correctly before an emissions test.

Frequently asked questions

How much does it cost to replace vapor canisters on a Workhorse Fastrack Ft1601?
Parts start at low prices at AutoBuffy. The canister itself is the main cost; professional labor typically adds one to two hours of shop time depending on location. DIY replacement keeps the total lower since the job usually requires basic hand tools and no specialized equipment.
Can I drive my Workhorse Fastrack Ft1601 with a bad vapor canister?
You can drive short distances, but it is not advisable. A saturated or cracked canister vents raw fuel vapors into the atmosphere and can cause fuel odor inside the cabin. It will also keep the check engine light on, mask other faults, and cause your Workhorse Fastrack Ft1601 to fail an emissions inspection until it is repaired.
Will replacing the vapor canister fix my EVAP check engine light?
It depends on the specific fault code. Codes like P0440 or P0446 often point to the canister itself or its vent valve. However, EVAP faults can also come from a leaking gas cap, purge solenoid, vent solenoid, or cracked hose. Diagnose the exact code before replacing the canister to confirm it is the root cause.
How long does a vapor canister last on a Workhorse Fastrack Ft1601?
Most vapor canisters last the life of the vehicle under normal conditions. Premature failure is typically caused by overfilling the fuel tank repeatedly, which forces liquid fuel into the canister and saturates or damages the charcoal media. Physical cracks from road debris or heat cycling are the other common cause of early replacement.
Do I need to replace the vapor canister filter at the same time?
Yes, it is strongly recommended. The canister vent filter prevents dirt and moisture from entering the charcoal bed. If the canister failed due to contamination, a clogged or damaged vent filter is often a contributing cause. Replacing both together at the same time prevents the new canister from being exposed to the same conditions that damaged the original.
Where is the vapor canister located on a Workhorse Fastrack Ft1601?
On most Workhorse Fastrack Ft1601 vehicles the vapor canister is mounted near the fuel tank, typically underneath the vehicle toward the rear or inside the engine bay near the firewall. Location varies by generation and body style. Consulting a vehicle-specific diagram before starting the job will save time identifying the canister and its connected hoses and brackets.

More parts for your Workhorse Fastrack Ft1601

Exhaust Flange Stud and NutEngine Oil PanEngine Valve CoverExhaust ManifoldAccessory Drive Belt Idler PulleyEngine Crankshaft Position Sensor ConnectorExhaust Manifold Bypass GasketVapor Canister Purge Valve

Vapor canisters for other Workhorse models

Workhorse FasTrack FT1801Workhorse FasTrack FT1061Workhorse W62Workhorse W16Workhorse R26Workhorse W21