Loading...

Bmw 328I Engine Oil Filter Housings

Bmw 328I Engine oil filter housings

Engine oil filter housings for the Bmw 328I start at $100.95. We stock 7 options from SKP, URO, and Standard Ignition. The oil filter housing is the threaded or bolted assembly that holds the oil filter element against the engine block, maintaining pressurized oil flow to critical components. A cracked, warped, or stripped housing leaks oil externally, starves the engine of lubrication, and can cause rapid engine damage if ignored.

Signs your Bmw 328I needs a new engine oil filter housing

  • Visible oil puddle or wet residue directly beneath the oil filter location on the engine block
  • Oil weeping or seeping from the housing seam, drain plug port, or threaded cap area
  • Persistent low oil pressure warning light after verifying oil level is correct
  • Oil burning smell from the engine bay caused by leaked oil contacting hot exhaust components nearby
  • Oil filter loosens or will not seat correctly because housing threads are stripped or cross-threaded
  • Recurring oil leaks that return immediately after replacing the filter gasket or O-ring, pointing to a warped or cracked housing body

Which engine oil filter housing should you buy for your Bmw 328I?

The main decision is whether to replace the full housing assembly or just its internal components such as the O-ring kit, drain plug, or bypass valve. Most housing failures on the Bmw 328I are caused by deteriorated seals or cracked plastic bodies, so knowing which part has failed saves money. Material — plastic composite versus aluminum — also affects longevity and suitability for high-heat applications.

OEM-equivalent replacement housing
Best for
Restoring factory fit and function with no modifications
What you get
Full housing body matched to original dimensions, correct port locations, and factory-spec material
Housing with O-ring and seal kit included
Best for
Addressing a leak caused by worn seals without sourcing parts separately
What you get
Complete housing plus all gaskets, O-rings, and drain plug needed for a one-step repair
Upgraded aluminum housing
Best for
High-mileage engines or performance builds that run higher oil temperatures
What you get
Greater heat resistance and crack resistance than plastic OEM housings; typically heavier
O-ring and seal kit only (no housing body)
Best for
Housing body is intact but leaking only at sealing surfaces
What you get
Replacement seals and gaskets at lower cost when the housing itself is undamaged

Engine oil filter housings brands we stock for your Bmw 328I

SKP
2 options · from $100.95
URO
2 options · from $233.95
Standard Ignition
1 option · from $308.95
VEMO
1 option · from $370.95
Vaico
1 option · from $395.95

Replacing the engine oil filter housing on a Bmw 328I

Moderate⏱ 1–2 hoursOil filter housing cap wrench or large socket matching the housing cap sizeSocket set and ratchet with extensionsDrain panTorque wrenchPick tool or small screwdriver for O-ring removal

Begin by draining the engine oil and removing the old filter to relieve residual oil in the housing. Unbolt or unthread the housing from the engine block, taking care not to damage coolant lines or sensors attached nearby on some Bmw 328I configurations. Install the new housing or seals, hand-tighten first, then bring fasteners to the manufacturer-specified torque range — finger-tight plus a controlled final turn is typically sufficient for plastic cap housings to avoid cracking.

Frequently asked questions

How much does it cost to replace engine oil filter housings on a Bmw 328I?
Parts start at $100.95 for a Bmw 328I oil filter housing. A full assembly with seals costs more than a seal-only kit. Add shop labor of one to two hours if you are not doing it yourself. Catching a housing leak early prevents far more expensive repairs like a seized engine from oil starvation.
Can I drive my Bmw 328I with a leaking oil filter housing?
No. Even a slow oil filter housing leak on a Bmw 328I will progressively worsen under engine heat and oil pressure. Continuing to drive risks dropping oil level to a point where the engine loses adequate lubrication, leading to accelerated wear or catastrophic bearing failure. Check the oil level immediately and arrange repair before driving further.
Is the oil filter housing the same as the oil filter adapter on a Bmw 328I?
They are closely related but not identical. The oil filter housing is the canister or cup that physically contains the filter element. The oil filter adapter is a separate threaded block that connects the housing to the engine block and routes oil ports. Some Bmw 328I designs combine both into one assembly; others keep them separate.
How long does an oil filter housing last on a Bmw 328I?
Plastic oil filter housings on the Bmw 328I typically last many years but become brittle with age and heat cycling, making them prone to cracking after a decade or more of use. Internal O-rings and seals wear out sooner. Replacing seals at regular oil change intervals and avoiding overtightening the filter cap helps extend housing life significantly.
What causes an oil filter housing to crack or fail on a Bmw 328I?
The most common causes on a Bmw 328I are overtightening the filter cap, long-term heat cycling that embrittles plastic housings, using the wrong oil filter that stresses the housing threads, and deferred maintenance that allows O-rings to harden and crack. Physical impact from road debris or during other underhood repairs can also crack the housing body.
Do I need to replace the entire housing or just the O-ring on my Bmw 328I?
Inspect the housing body carefully before ordering. If the Bmw 328I housing body is visibly cracked, warped at the sealing face, or has stripped threads, replace the full assembly. If the body is structurally sound and only sealing surfaces are leaking, an O-ring and seal kit is the correct and more economical fix.

Shop engine oil filter housings by year for the Bmw 328I

201620152014201320122011201020092008200720001999199819971996

More parts for your Bmw 328I

Engine Water PumpEngine Oil Drain PlugExhaust NutDisc Brake Pad Retaining ClipEngine Variable Valve Timing (VVT) Eccentric Shaft Sensor SealMass Air Flow Sensor AssemblyWheel Bearing & Hub SetDisc Brake Caliper Guide Bushing Kit

Engine oil filter housings for other Bmw models

Bmw 840CiBmw 328isBmw M4Bmw 525iBmw 335i xDriveBmw Z8