Loading...

Jaguar S Type ABS Wheel Speed Sensors

Jaguar S Type Abs wheel speed sensors

Starting at low prices, AutoBuffy stocks multiple ABS wheel speed sensors from top OE-quality brands for the Jaguar S Type. This sensor monitors wheel rotation speed and sends data to the ABS control module so it can prevent wheel lockup during hard braking. A failed sensor disables ABS entirely, leaving you without anti-lock protection when it matters most.

Signs your Jaguar S Type needs a new ABS wheel speed sensor

  • ABS warning light is illuminated on the dashboard and will not clear after restarting
  • Traction control or stability control warning light appears alongside or instead of the ABS light
  • ABS activates unnecessarily on dry pavement at low speeds or during normal stops
  • Wheels lock up during hard braking as if the ABS system is not functioning at all
  • Speedometer reads erratically or drops to zero intermittently while driving
  • Stored diagnostic trouble codes in the C1200–C1299 range pointing to a specific wheel sensor circuit

Which ABS wheel speed sensor should you buy for your Jaguar S Type?

The most important decision is choosing the correct wheel position — front-left, front-right, rear-left, or rear-right — since each sensor has a specific connector, harness length, and mounting configuration. Beyond position, you'll choose between OE-replacement and premium upgraded sensors, which differ in connector quality, magnet design, and resistance to heat and corrosion.

OE-Equivalent Replacement
Best for
Restoring factory function at the lowest cost
What you get
Direct plug-and-play fit, matches original signal output, no calibration needed
Premium / OE-Grade Upgrade
Best for
High-mileage vehicles or harsh climates
What you get
Reinforced wiring harness, better corrosion-resistant housing, tighter signal tolerance
Active (Magnetic) Sensor
Best for
Vehicles requiring a powered Hall-effect sensor
What you get
Wider air gap tolerance, consistent signal at very low wheel speeds, works with tone rings
Passive (Inductive) Sensor
Best for
Older Jaguar S Type applications with a toothed reluctor ring
What you get
No external power needed, simple two-wire design, lower cost, proven reliability

Replacing an ABS wheel speed sensor on a Jaguar S Type

Moderate⏱ 1–2 hours per sensorSocket set and ratchetPenetrating oil (for corroded mounting bolts)Flathead screwdriver or trim tool (for harness clips)OBD-II scan tool (to clear ABS codes after installation)Wire brush (to clean the mounting bore and tone ring)

Remove the wheel, disconnect the sensor harness connector, and unbolt the sensor from its mounting point on the knuckle or hub — penetrating oil is often needed on corroded fasteners. Route the new sensor's harness through the factory clips exactly as the original, snug the mounting bolt to firm resistance without overtightening, and reconnect the harness. Clear the ABS fault codes with a scan tool and perform a short test drive above 15 mph to confirm the warning light stays off.

Frequently asked questions

How much does it cost to replace ABS wheel speed sensors on a Jaguar S Type?
Parts start at low prices on AutoBuffy for the Jaguar S Type. A single sensor is typically the only part needed. DIY installation keeps total cost near that parts price, while a shop will add one to two hours of labor. Replacing just the failed sensor — confirmed by a scan tool — avoids unnecessary expense.
Can I drive my Jaguar S Type with a bad ABS wheel speed sensor?
You can drive short distances, but it is not recommended. A failed sensor disables the ABS system, meaning your wheels can lock during hard braking and you lose anti-lock, traction control, and often stability control functions simultaneously. Normal braking still works, but your safety margin in emergency stops is significantly reduced.
Will a bad ABS sensor cause the traction control light to come on my Jaguar S Type?
Yes. Traction control and stability control on the Jaguar S Type rely on the same wheel speed data as the ABS module. A faulty or missing signal from one sensor causes the control module to disable both ABS and traction control together, which is why both warning lights commonly illuminate at the same time.
Do I need to replace all four ABS sensors or just the one that failed on my Jaguar S Type?
Replace only the confirmed bad sensor. Use a scan tool to pull ABS fault codes — they identify the exact wheel position with the circuit fault. Unless multiple sensors show codes or the vehicle has extremely high mileage with visible corrosion across all sensors, replacing one at a time is the correct and cost-effective approach.
How do I know if my Jaguar S Type has an active or passive ABS wheel speed sensor?
Check the wire count at the sensor connector. A passive (inductive) sensor uses two wires and generates its own AC signal from wheel rotation. An active (Hall-effect) sensor uses three wires and requires a power supply. Your Jaguar S Type owner's manual, a factory service diagram, or AutoBuffy's fitment filter will confirm the correct type.
Can a dirty or damaged tone ring cause the same symptoms as a bad ABS sensor on my Jaguar S Type?
Yes, and this is a common misdiagnosis. The tone ring — a toothed reluctor ring on the axle or hub — must be clean and undamaged for the sensor to read correctly. A cracked tooth, packed rust, or debris gap produces an irregular signal that mimics sensor failure. Inspect the tone ring before condemning the sensor.

Abs wheel speed sensors for other Jaguar models

Jaguar XJ8Jaguar Super V8Jaguar Vanden PlasJaguar XJ12Jaguar S-TypeJaguar XFR