Loading...

Chevrolet C50 Fuel Pump Pressure Switch Connectors

Chevrolet C50 Fuel pump pressure switch connectors

Starting at $60.95, AutoBuffy stocks 1 fuel pump pressure switch connectors from Standard Ignition for the Chevrolet C50. This connector carries the electrical signal between the fuel pump pressure switch and the engine control module, telling the system whether fuel pressure is within range. A corroded or broken connector can trigger false codes, stall the engine, or prevent it from starting.

Signs your Chevrolet C50 needs a new fuel pump pressure switch connector

  • Engine cranks but won't start even though the fuel pump is known to be working
  • Intermittent stalling at idle or under load that clears when the wiring harness is wiggled
  • Check engine light with a fuel system pressure or fuel pump circuit fault code stored
  • Fuel pump runs continuously or fails to shut off after the engine is turned off
  • Erratic fuel trim readings or the engine running rich or lean without an obvious cause
  • Visible melting, cracking, or green corrosion at the connector body or terminal pins

Which fuel pump pressure switch connector should you buy for your Chevrolet C50?

The main decision is whether to buy an OE-spec connector pigtail, a universal repair connector, or a full wiring harness repair kit. Fit and terminal quality matter most here — a loose or corroded terminal will recreate the original fault. Match the number of pins and connector lock style to the factory plug before ordering.

OE-spec pigtail connector
Best for
Direct bolt-on replacement with no modification
What you get
Pre-terminated pigtail cut to length, correct terminal count and lock tab, matches factory resistance spec
Universal repair connector
Best for
Budget repair when exact pigtail is unavailable
What you get
Generic housing with compatible terminals, requires splicing and heat-shrink sealing, lower cost but more labor
Weatherproof connector kit
Best for
High-moisture environments or previous corrosion damage
What you get
Sealed connector housing with silicone-filled terminals, resists fuel vapor and road spray better than standard open connectors
Full wiring harness section
Best for
Extensive chafing or melting beyond just the connector end
What you get
Longer section of pre-made harness including connector, covers damaged wire runs rather than just the terminal end

Fuel pump pressure switch connectors brands we stock for your Chevrolet C50

Standard Ignition
1 option · from $60.95

Replacing a fuel pump pressure switch connector on a Chevrolet C50

Easy30–60 minutesMultimeterTerminal pick or pick setWire stripper and crimperHeat gun and adhesive heat-shrink tubingElectrical contact cleaner

Disconnect the battery before starting, then locate the pressure switch on the fuel rail or fuel line and unplug the damaged connector. Release any locking tab carefully with a pick to avoid breaking the switch body, then cut the pigtail back to clean wire, strip the ends, and splice the new connector using crimp connectors sealed with heat-shrink tubing. Reconnect the battery, clear any stored codes, and verify the correct pressure signal with a scan tool before considering the repair complete.

Frequently asked questions

How much does it cost to replace fuel pump pressure switch connectors on a Chevrolet C50?
Parts start at $60.95 for the Chevrolet C50. The connector itself is inexpensive, but total cost depends on whether a shop charges diagnostic time to isolate the connector as the fault versus the switch or pump. DIY replacement is straightforward and keeps the job to just the part cost plus basic supplies.
Can a bad fuel pump pressure switch connector cause a no-start on a Chevrolet C50?
Yes. If the connector is open-circuit due to corrosion or a broken terminal, the ECM receives no pressure signal and may disable the fuel pump relay as a safety measure. The engine will crank without starting. Confirming power and ground at the connector pins with a multimeter is the fastest way to verify this fault.
Is the fuel pump pressure switch connector the same as the fuel pump connector on a Chevrolet C50?
No, they are separate components. The fuel pump connector supplies power directly to the pump motor. The pressure switch connector carries a low-current signal wire that reports fuel rail or line pressure to the ECM. Swapping one for the other will not work — confirm which connector is faulty before ordering.
How do I know if the connector is bad versus the pressure switch itself on a Chevrolet C50?
Unplug the connector and inspect terminals for corrosion, pushed-back pins, or melted plastic. Then backprobe the connector with a multimeter to check for reference voltage and clean ground. If voltage is present at the harness side but the signal is still incorrect, the switch is likely the fault rather than the connector.
Will a corroded fuel pump pressure switch connector throw a specific code on a Chevrolet C50?
Usually yes. A failing connector typically sets a fuel pressure sensor circuit low, high, or range/performance code depending on how the terminal is failing. The exact code varies by platform. Clearing the code and wiggling the connector harness while monitoring live data is a quick way to confirm an intermittent connector fault.
How long does a fuel pump pressure switch connector last on a Chevrolet C50?
Connector lifespan varies widely based on environment. Exposure to fuel vapors, heat cycles near the engine or fuel tank, and road moisture all accelerate terminal corrosion and plastic embrittlement. Connectors in high-heat or high-humidity climates often degrade sooner than those in dry conditions, making periodic visual inspection worthwhile during other fuel system service.

Shop fuel pump pressure switch connectors by year for the Chevrolet C50

More parts for your Chevrolet C50

Fuel pump pressure switch connectors for other Chevrolet models