Loading...

Ford Figo Engine Intake Manifold Runner Control Sensor Connectors

Ford Figo Engine intake manifold runner control sensor connectors

Starting at $68.95, AutoBuffy stocks 1 engine intake manifold runner control sensor connectors from Standard Ignition. This connector links the manifold runner control (IMRC) sensor to the ECU, transmitting butterfly valve position data that governs airflow and fuel trim. A damaged or corroded connector breaks that signal, triggering misfires, rough idle, and a check engine light that won't clear.

Signs your Ford Figo needs a new intake manifold runner control sensor connector

  • Check engine light with stored codes P2004, P2006, P2008, or related IMRC fault codes
  • Rough or unstable idle caused by incorrect airflow readings sent to the ECU
  • Noticeable hesitation or stumble during acceleration, especially at low RPM
  • Reduced fuel economy as the ECU compensates for bad sensor signal with incorrect fuel trims
  • Failed emissions test due to elevated hydrocarbon output from poor combustion control
  • Intermittent or hard no-start conditions when connector corrosion causes a complete loss of signal

Which intake manifold runner control sensor connector should you buy for your Ford Figo?

The main buying decision comes down to terminal count, wire gauge compatibility, and whether the connector includes a pre-wired pigtail or is a bare housing. Matching the exact terminal count and lock-tab style to the original connector is critical — an incorrect fit causes a poor seal and repeat failures. OE-style connectors with weather-resistant seals last significantly longer than generic equivalents in high-heat engine bay environments.

OE-match pigtail connector (pre-wired)
Best for
DIYers who want a plug-and-play repair with minimal soldering
What you get
Correct terminal count, matching wire colors, weatherproof seal, and 6–12 inches of pre-stripped wire ready to splice
Bare connector housing with terminals
Best for
Shops or experienced DIYers reusing existing wiring
What you get
Housing and loose terminals only — requires terminal crimping tools and knowledge of the original wire gauge
Connector repair kit (multi-piece)
Best for
Vehicles with corroded terminals AND damaged wiring
What you get
Includes housing, terminals, seals, and wire — covers the full connector assembly for a complete restoration
OEM dealer connector
Best for
Owners who require exact factory fitment and are less price-sensitive
What you get
Direct factory replacement with guaranteed fitment, but typically higher cost and longer lead time

Engine intake manifold runner control sensor connectors brands we stock for your Ford Figo

Standard Ignition
1 option · from $68.95

Replacing the intake manifold runner control sensor connector on a Ford Figo

Moderate⏱ 30–90 minutesDigital multimeterTerminal pick or connector release toolWire stripper and crimping toolHeat-shrink butt connectors or soldering iron and electrical tapeRatchet and socket set (for intake cover removal if needed)

Begin by disconnecting the battery negative terminal, then locate the IMRC sensor on the intake manifold and depress the connector lock tab to unplug it. If using a pigtail connector, strip the existing wires and splice the new connector using heat-shrink butt connectors or solder and adhesive-lined heat shrink for a weatherproof join. Reconnect the battery, clear any stored fault codes with a scan tool, and verify the repair with a short test drive to confirm codes do not return.

Frequently asked questions

How much does it cost to replace intake manifold runner control sensor connectors on a Ford Figo?
The connector itself starts at $68.95 at AutoBuffy. Total repair cost depends on whether you DIY or use a shop. A professional splice-and-install typically adds one to two hours of labor. Catching this early avoids the larger expense of replacing the IMRC sensor or the full manifold runner control assembly.
Can a bad IMRC sensor connector cause a P2004 or P2006 code on my Ford Figo?
Yes. Codes P2004 and P2006 indicate the intake manifold runner is stuck open or closed, but a corroded or broken connector feeding the sensor bad voltage is a common root cause. Always inspect and test the connector before condemning the sensor or the IMRC actuator motor itself.
Is it safe to drive my Ford Figo with a faulty intake manifold runner control sensor connector?
Short distances are generally possible, but it is not advisable. A broken IMRC signal leaves the ECU running open-loop or on a default map, reducing performance and fuel economy. Extended driving in this condition can cause incomplete combustion, catalytic converter stress, and potentially a failed emissions inspection.
How do I know if the connector is the problem and not the IMRC sensor itself on my Ford Figo?
Use a digital multimeter to check for reference voltage and ground at the connector terminals with the key on. Also inspect for bent pins, green corrosion, or cracked weatherproofing. If voltage is absent or erratic at the connector but the wiring harness tests good upstream, the connector is the fault.
Do I need to match the exact terminal count when buying a replacement connector for my Ford Figo?
Yes — terminal count must match exactly. IMRC sensor connectors vary by engine design and can have two, three, or four terminals. Using a connector with the wrong terminal count will result in an incorrect fit, exposed terminals, and a connection that fails to seal against moisture and heat.
How long does an intake manifold runner control sensor connector last on a Ford Figo?
Connector lifespan varies widely based on engine bay heat, moisture exposure, and road salt. Many last the life of the vehicle, but connectors positioned near the top of the intake or close to heat sources tend to degrade sooner. Inspect the connector any time you replace the IMRC sensor or diagnose related codes.

Shop engine intake manifold runner control sensor connectors by year for the Ford Figo

20202019201820172016

More parts for your Ford Figo

Engine Oil FilterBare Strut SetShock Absorber SetRadiator Coolant HoseStrut MountSerpentine BeltDrum Brake Hardware KitEngine Coolant Temperature Sensor Connector

Engine intake manifold runner control sensor connectors for other Ford models

Ford F-53 Motorhome ChassisFord FreestarFord E-350 Super DutyFord E-450 Super DutyFord F-550 Super DutyFord Focus