Loading...
Ford Granada Stabilizer Bar Bushing Kits
Ford Granada Stabilizer bar bushing kits
Starting at $3.95, AutoBuffy stocks 25 stabilizer bar bushing kits from Delphi, Mevotech Original Grade, and Mevotech Supreme for the Ford Granada. These rubber or polyurethane sleeves clamp the sway bar to the subframe, controlling body roll in corners. When they wear out, the bar shifts and knocks, handling becomes vague, and uneven tire wear follows.
Signs your Ford Granada needs new stabilizer bar bushing kits
- Clunking or knocking noise from the front or rear suspension over bumps, dips, or rough pavement
- Rhythmic thumping that changes with vehicle speed or road surface texture
- Noticeable body lean or excessive roll when cornering at moderate speeds
- Steering feels loose or imprecise, especially during lane changes
- Vibration felt through the floorboard or steering wheel at low speeds over rough roads
- Visible cracking, splitting, or flattening of the rubber bushing when inspected under the vehicle
Which stabilizer bar bushing kit should you buy for your Ford Granada?
The two main decisions are material — rubber versus polyurethane — and whether you need front, rear, or both positions. OE-spec rubber kits restore factory feel and noise isolation, while polyurethane kits firm up handling at the cost of slightly more NVH. Make sure the inner diameter matches your Ford Granada's sway bar diameter exactly, as even a few millimeters of mismatch causes premature wear or persistent noise.
OE Rubber Replacement
Best for
Daily drivers, comfort-focused owners
What you get
Factory-equivalent feel, quiet ride, easy install, shorter lifespan than poly
Polyurethane Upgrade
Best for
Performance or spirited driving, longer service life
What you get
Firmer cornering response, higher durability, may transmit slightly more road noise
Front Bushing Kit
Best for
Clunking or vague steering originating from front axle
What you get
Bushings sized and shaped for the front sway bar mount locations on the Ford Granada
Complete Front + Rear Kit
Best for
High-mileage vehicles or full suspension refresh
What you get
Both axle positions covered in one order, consistent material and wear rate across all four mounts
| Option | Best for | What you get |
|---|---|---|
| OE Rubber Replacement | Daily drivers, comfort-focused owners | Factory-equivalent feel, quiet ride, easy install, shorter lifespan than poly |
| Polyurethane Upgrade | Performance or spirited driving, longer service life | Firmer cornering response, higher durability, may transmit slightly more road noise |
| Front Bushing Kit | Clunking or vague steering originating from front axle | Bushings sized and shaped for the front sway bar mount locations on the Ford Granada |
| Complete Front + Rear Kit | High-mileage vehicles or full suspension refresh | Both axle positions covered in one order, consistent material and wear rate across all four mounts |
Stabilizer bar bushing kits brands we stock for your Ford Granada
Delphi
7 options · from $9.95
Mevotech Original Grade
6 options · from $5.95
Mevotech Supreme
6 options · from $6.95
ACDelco
2 options · from $11.95
MOOG
2 options · from $10.95
Dorman
1 option · from $8.95
SKP
1 option · from $3.95
Replacing stabilizer bar bushing kits on a Ford Granada
Easy⏱ 30–90 minutesFloor jack and jack stands or a vehicle liftSocket set and ratchetCombination wrench setBushing grease (lithium or PTFE-based)Wire brush or sandpaper for cleaning the sway bar
With the Ford Granada safely raised and supported, remove the bushing bracket bolts, slide the old bushings off the sway bar, and clean the bar surface before installing the new bushings. Polyurethane bushings should be greased before the brackets are torqued down. Snug the bracket bolts with the suspension at ride height to prevent binding, following the service manual's fastener sequence for the Ford Granada.
Frequently asked questions
How much does it cost to replace stabilizer bar bushing kits on a Ford Granada?
Parts start at $3.95 for the Ford Granada. A complete DIY job costs only the parts plus a tube of bushing grease. Shop labor typically adds one to two hours of labor time. Replacing bushings at the same time as end links saves a second lift appointment and is generally recommended when either component shows wear.
How long do stabilizer bar bushings last on a Ford Granada?
Rubber bushings on the Ford Granada commonly last several years under normal driving but degrade faster in extreme climates, on rough roads, or when exposed to oil or brake fluid leaks. Polyurethane bushings generally outlast rubber by a significant margin. Inspect them any time the vehicle is on a lift for other suspension work.
Can I drive my Ford Granada with worn stabilizer bar bushings?
Worn bushings on the Ford Granada rarely cause immediate safety failure, but they allow the sway bar to shift under load, reducing cornering stability and predictability. Continued driving with severely deteriorated bushings can accelerate wear on the sway bar itself and end links. Replacing them promptly is low-cost insurance against more expensive damage.
Do I need to replace the sway bar end links at the same time on my Ford Granada?
Not always, but it is strongly recommended. End links and bushings wear at similar rates on the Ford Granada, and a failed end link produces the same clunking symptoms. If the end links show any play, torn boots, or corrosion, replacing both components together eliminates the noise completely and avoids a repeat repair in the near future.
Do polyurethane stabilizer bar bushings require grease on the Ford Granada?
Yes. Unlike rubber bushings, polyurethane bushings on the Ford Granada require a coating of the included or separately purchased lithium- or PTFE-based grease at installation. Skipping this step causes squeaking as the bushing rotates slightly against the bar. Re-greasing may be needed at long service intervals to maintain a quiet, rattle-free installation.
How do I know if the noise on my Ford Granada is the bushings and not the end links?
With the Ford Granada safely on a lift, grab the sway bar and attempt to move it up, down, and side to side. Clunking with lateral movement typically points to worn frame bushings. Clunking with up-and-down movement at the bar's ends usually indicates failed end links. Both tests together quickly isolate which component is the source.