Loading...

Honda S2000 Door Hinge Pins

Honda S2000 Door hinge pins

Door hinge pins for your Honda S2000 start at $10.95, and AutoBuffy stocks 1 options from SKP. The hinge pin is the steel rod that holds each door hinge knuckle together, letting the door swing open and closed smoothly. When it wears out, the door sags, binds, and can damage the body — catching it early prevents costly panel repairs.

Signs your Honda S2000 needs new door hinge pins

  • Door sags visibly when fully open, dropping lower than its normal resting position
  • Door scrapes or drags against the body sill or A-pillar when opening or closing
  • Loud clunking, popping, or squeaking noise as the door swings
  • Door latch no longer aligns with the striker — requires lifting the door to close it fully
  • Visible side-to-side or up-and-down slop when you grab the door edge and shake it
  • Uneven gap between the door and body that was not present before

Which door hinge pins should you buy for your Honda S2000?

Door hinge pins vary mainly by material, whether they come as bare pins or as a complete kit with bushings and snap rings, and which door position they fit. Replacing the pin alone into a worn bushing rarely solves the sag — most mechanics recommend buying a kit. Match the kit to the correct door position (front or rear) and driver or passenger side.

Pin-only replacement
Best for
Hinge bushing is still tight; pin is the only worn part
What you get
Single hardened steel pin, usually requires pressing
Pin and bushing kit
Best for
Most common repair; both pin and bushing are worn
What you get
Matching pin, bronze or nylon bushings, snap rings — full rebuild
Complete hinge assembly
Best for
Pin and bushing are severely worn or hinge knuckle is cracked or bent
What you get
Ready-to-bolt hinge; no pressing required, fastest install
Heavy-duty / greaseable kit
Best for
High-use doors, trucks, or vehicles driven in harsh conditions
What you get
Oversized hardened pin with grease fitting for ongoing lubrication

Door hinge pins brands we stock for your Honda S2000

SKP
1 option · from $10.95

Replacing door hinge pins on a Honda S2000

Moderate⏱ 1–2 hoursPin punch setBall-peen or dead-blow hammerFloor jack or door support standSnap ring pliers (if kit uses snap rings)Grease or penetrating oil

Support the door with a jack stand or assistant so it cannot drop when the pin is removed. Drive out the old pin using a punch from the bottom up, remove worn bushings, and press or tap new bushings and the new pin into place until snap rings seat fully. Check door alignment and adjust the striker if needed so the latch engages without lifting the door.

Frequently asked questions

How much does it cost to replace door hinge pins on a Honda S2000?
Parts start at $10.95 for a pin and bushing kit for your Honda S2000. A complete set covering both hinges on one door typically runs more. If you pay a shop, expect one to two hours of labor on top of parts cost. DIY replacement with basic hand tools keeps the total close to the parts price alone.
Can I drive my Honda S2000 with worn door hinge pins?
You can drive short distances, but it is not advisable for long. A sagging door puts stress on the latch and striker, can crack the door shell, and may swing uncontrollably in a turn or on a slope. In a collision, a door that does not hang correctly may not protect occupants as designed.
Do I need to replace the bushing when I replace the hinge pin on my Honda S2000?
Yes, in almost every case. The pin and bushing wear together. Installing a new pin into a worn bushing leaves excessive clearance, and the door will continue to sag. Buying a kit that includes both the pin and matching bushings ensures the tolerances are correct and the repair lasts.
How long do door hinge pins last on a Honda S2000?
Lifespan varies widely based on use, climate, and whether the hinges were ever lubricated. On many vehicles they last well over a decade with periodic greasing. Doors that are used heavily, exposed to road salt, or never lubricated can wear out significantly sooner. Squeaking or minor sag are early warnings to act on.
Is replacing door hinge pins on a Honda S2000 a DIY job?
Most pin and bushing kits are a DIY-friendly job with basic hand tools and a pin punch. The door must be supported while the old pin is driven out and the new one installed. A complete hinge replacement is even more straightforward — bolt-off, bolt-on. Neither job typically requires specialty equipment.
How do I know if my Honda S2000 has worn hinge pins versus a bent hinge or misadjusted door?
Grab the door edge with both hands and try to move it up and down and side to side with the door open about 90 degrees. Loose play at the hinge pivot points to worn pins or bushings. A bent hinge or misadjusted striker produces a consistent offset gap with no play felt at the hinge itself.

Shop door hinge pins by year for the Honda S2000

2009200820072006200520042003200220012000

More parts for your Honda S2000

Engine Variable Valve Timing (VVT) Oil Pressure SwitchExhaust Pipe Flange GasketIdle Air Control ValveA/C CompressorA/C Receiver DrierStarterStarter SolenoidA/C System Valve Core and Cap Kit

Door hinge pins for other Honda models

Honda InsightHonda CRXHonda WagovanHonda ClarityHonda AccordHonda Pilot