Loading...

Jeep Scrambler Alignment Caster / Camber Bushings

Jeep Scrambler Alignment caster / camber bushings

Starting at low prices, AutoBuffy stocks multiple alignment caster/camber bushings from top OE-quality brands. These rubber or polyurethane bushings mount inside the control arm or subframe to set the precise angle at which your wheels sit and sweep. When they crack, collapse, or shift, your Jeep Scrambler loses its alignment geometry — causing uneven tire wear, pull, and handling instability that realignment alone cannot fix.

Signs your Jeep Scrambler needs new alignment caster/camber bushings

  • Tires wear unevenly on one edge (inner or outer) even after a fresh wheel alignment
  • Steering pulls consistently to one side on a flat, straight road
  • Alignment angles drift back out of spec shortly after a professional alignment
  • Clunking or knocking felt through the steering wheel or floorboard over bumps
  • Visible rubber tearing, cracking, or collapse when inspecting the control arm pivot points
  • Rear end feels loose or 'crabbing' sideways, especially during acceleration or lane changes

Which alignment caster/camber bushing should you buy for your Jeep Scrambler?

The main decisions are material (OE-rubber vs. polyurethane), whether you need an eccentric/adjustable bushing to dial in corrected geometry, and whether you're replacing a single worn piece or doing both sides as a set. Confirm the specific control arm location — front lower, front upper, or rear — because bushing geometry differs by position and a mismatch will throw off your alignment targets.

OE-Replacement Rubber Bushing
Best for
Daily drivers wanting stock ride quality and easy installation
What you get
Factory-matched durometer, absorbs NVH well, straightforward press-in fit with standard alignment specs
Polyurethane Bushing
Best for
Performance or high-mileage vehicles needing longer service life
What you get
Firmer feel, resists oil and ozone degradation, reduces deflection for more consistent alignment — some added harshness on rough roads
Eccentric / Offset Adjustable Bushing
Best for
Vehicles with worn subframes, lifted/lowered suspensions, or out-of-range camber/caster
What you get
Rotating offset sleeve lets a technician dial in alignment angles beyond the factory adjustment range
Bushing Kit (Axle Set)
Best for
Complete refresh or when one side shows wear that suggests the other is close behind
What you get
Both left and right bushings matched in material and spec, often at a lower per-unit cost than buying singles

Replacing alignment caster/camber bushings on a Jeep Scrambler

Advanced⏱ 2–4 hoursHydraulic floor jack and jack standsBushing press or hydraulic press (bench or in-vehicle cup set)Breaker bar and metric/standard socket setTorque wrenchPenetrating oil

Caster/camber bushings are pressed into the control arm housing or subframe bracket, so removal requires a proper bushing press or a hydraulic press with the correct cup adapters — driving them out with a hammer risks damaging the housing bore. The control arm must be unloaded from suspension weight before loosening the pivot hardware, and all fasteners should be torqued with the suspension at ride height to prevent bushing wind-up. Because this job directly affects alignment geometry, a professional four-wheel alignment is mandatory as the final step.

Frequently asked questions

How much does it cost to replace alignment caster / camber bushings on a Jeep Scrambler?
Parts start at low prices on AutoBuffy. Budget additionally for professional labor, which typically ranges from one to two hours per axle depending on how accessible the control arm pivot is. A follow-up wheel alignment is always required after this repair, so factor that shop fee into your total cost estimate.
Can I drive my Jeep Scrambler with worn alignment caster/camber bushings?
You can drive short distances, but it is not advisable. Collapsed bushings allow control arm movement outside its intended arc, which destabilizes steering response and accelerates tire wear. In severe cases the bushing can separate entirely, leading to sudden loss of directional control. Replace them promptly once wear is confirmed.
Will replacing the alignment caster / camber bushings on my Jeep Scrambler fix my alignment by itself?
No. Installing new bushings restores the suspension geometry back to its adjustable range, but a professional four-wheel alignment must be performed immediately afterward. New bushings alone do not set caster or camber to spec — they simply allow the alignment to be set correctly and to hold those settings over time.
How long do alignment caster/camber bushings last on a Jeep Scrambler?
OE rubber bushings typically last anywhere from 50,000 to over 100,000 miles depending on road conditions, climate, and driving style. Exposure to road salt, oil contamination, and frequent rough-road use shortens that range considerably. Polyurethane replacements generally outlast rubber in harsh environments but should still be inspected during every major suspension service.
Do I need an alignment after replacing alignment caster / camber bushings on my Jeep Scrambler?
Yes, every time — no exceptions. Caster and camber bushings are a direct part of the alignment geometry. Even if the new bushing is dimensionally identical to the old one, removing and reinstalling a control arm pivot disrupts the set angles. Skip the post-install alignment and you risk rapid tire wear and unpredictable handling.
Are eccentric caster/camber bushings worth it for a Jeep Scrambler?
Eccentric bushings are worth it when your Jeep Scrambler's alignment readings fall outside the factory adjustment range — common after a collision, subframe corrosion, or a suspension lift or lowering modification. They let a technician recover proper geometry without expensive structural repair. For a stock vehicle with angles still in range, standard replacement bushings are sufficient.

More parts for your Jeep Scrambler

Leaf Spring Shackle BushingLeaf Spring Axle U-Bolt KitHVAC Blower Control SwitchBrake Light SwitchTie Rod EndBrake RotorEngine Timing Crankshaft SprocketAlternator

Alignment caster / camber bushings for other Jeep models

Jeep CommandoJeep WagoneerJeep CherokeeJeep CJ6Jeep J10Jeep J20