Loading...

Lexus Nx350H Stabilizer Bar Bushing Kits

Lexus Nx350H Stabilizer bar bushing kits

Starting at $15.95, AutoBuffy stocks 1 stabilizer bar bushing kits from MOOG for the Lexus Nx350H. These rubber or polyurethane sleeves clamp the sway bar to the subframe, controlling body roll in corners. When they wear out, the bar shifts and knocks, handling becomes vague, and uneven tire wear follows.

Signs your Lexus Nx350H needs new stabilizer bar bushing kits

  • Clunking or knocking noise from the front or rear suspension over bumps, dips, or rough pavement
  • Rhythmic thumping that changes with vehicle speed or road surface texture
  • Noticeable body lean or excessive roll when cornering at moderate speeds
  • Steering feels loose or imprecise, especially during lane changes
  • Vibration felt through the floorboard or steering wheel at low speeds over rough roads
  • Visible cracking, splitting, or flattening of the rubber bushing when inspected under the vehicle

Which stabilizer bar bushing kit should you buy for your Lexus Nx350H?

The two main decisions are material — rubber versus polyurethane — and whether you need front, rear, or both positions. OE-spec rubber kits restore factory feel and noise isolation, while polyurethane kits firm up handling at the cost of slightly more NVH. Make sure the inner diameter matches your Lexus Nx350H's sway bar diameter exactly, as even a few millimeters of mismatch causes premature wear or persistent noise.

OE Rubber Replacement
Best for
Daily drivers, comfort-focused owners
What you get
Factory-equivalent feel, quiet ride, easy install, shorter lifespan than poly
Polyurethane Upgrade
Best for
Performance or spirited driving, longer service life
What you get
Firmer cornering response, higher durability, may transmit slightly more road noise
Front Bushing Kit
Best for
Clunking or vague steering originating from front axle
What you get
Bushings sized and shaped for the front sway bar mount locations on the Lexus Nx350H
Complete Front + Rear Kit
Best for
High-mileage vehicles or full suspension refresh
What you get
Both axle positions covered in one order, consistent material and wear rate across all four mounts

Stabilizer bar bushing kits brands we stock for your Lexus Nx350H

MOOG
1 option · from $15.95

Replacing stabilizer bar bushing kits on a Lexus Nx350H

Easy⏱ 30–90 minutesFloor jack and jack stands or a vehicle liftSocket set and ratchetCombination wrench setBushing grease (lithium or PTFE-based)Wire brush or sandpaper for cleaning the sway bar

With the Lexus Nx350H safely raised and supported, remove the bushing bracket bolts, slide the old bushings off the sway bar, and clean the bar surface before installing the new bushings. Polyurethane bushings should be greased before the brackets are torqued down. Snug the bracket bolts with the suspension at ride height to prevent binding, following the service manual's fastener sequence for the Lexus Nx350H.

Frequently asked questions

How much does it cost to replace stabilizer bar bushing kits on a Lexus Nx350H?
Parts start at $15.95 for the Lexus Nx350H. A complete DIY job costs only the parts plus a tube of bushing grease. Shop labor typically adds one to two hours of labor time. Replacing bushings at the same time as end links saves a second lift appointment and is generally recommended when either component shows wear.
How long do stabilizer bar bushings last on a Lexus Nx350H?
Rubber bushings on the Lexus Nx350H commonly last several years under normal driving but degrade faster in extreme climates, on rough roads, or when exposed to oil or brake fluid leaks. Polyurethane bushings generally outlast rubber by a significant margin. Inspect them any time the vehicle is on a lift for other suspension work.
Can I drive my Lexus Nx350H with worn stabilizer bar bushings?
Worn bushings on the Lexus Nx350H rarely cause immediate safety failure, but they allow the sway bar to shift under load, reducing cornering stability and predictability. Continued driving with severely deteriorated bushings can accelerate wear on the sway bar itself and end links. Replacing them promptly is low-cost insurance against more expensive damage.
Do I need to replace the sway bar end links at the same time on my Lexus Nx350H?
Not always, but it is strongly recommended. End links and bushings wear at similar rates on the Lexus Nx350H, and a failed end link produces the same clunking symptoms. If the end links show any play, torn boots, or corrosion, replacing both components together eliminates the noise completely and avoids a repeat repair in the near future.
Do polyurethane stabilizer bar bushings require grease on the Lexus Nx350H?
Yes. Unlike rubber bushings, polyurethane bushings on the Lexus Nx350H require a coating of the included or separately purchased lithium- or PTFE-based grease at installation. Skipping this step causes squeaking as the bushing rotates slightly against the bar. Re-greasing may be needed at long service intervals to maintain a quiet, rattle-free installation.
How do I know if the noise on my Lexus Nx350H is the bushings and not the end links?
With the Lexus Nx350H safely on a lift, grab the sway bar and attempt to move it up, down, and side to side. Clunking with lateral movement typically points to worn frame bushings. Clunking with up-and-down movement at the bar's ends usually indicates failed end links. Both tests together quickly isolate which component is the source.

Shop stabilizer bar bushing kits by year for the Lexus Nx350H

2025202420232022

More parts for your Lexus Nx350H

Brake RotorBrake Light SwitchManifold Absolute Pressure SensorRadiatorMulti-Purpose RelayIgnition CoilEngine Intake Manifold GasketBrake Pad & Rotor Kit

Stabilizer bar bushing kits for other Lexus models

Lexus SC400Lexus GX470Lexus ES300hLexus RX300Lexus GS450hLexus LX470