Chrysler 300 / Dodge Charger Front Suspension Kit (Control Arms + Tension Struts): What You Need to Know
MaintenanceNov 15, 2026•7

Chrysler 300 / Dodge Charger Front Suspension Kit (Control Arms + Tension Struts): What You Need to Know

Complete guide to front suspension kits for the Chrysler 300 and Dodge Charger—what's in the kit, costs, fitment differences, and how to buy right.

By AutoBuffy Team

Share:

The Short Answer

A front suspension kit for the Chrysler 300 or Dodge Charger typically includes lower control arms, tension struts, ball joints, and tie rod ends—and replacing them as a set, rather than one piece at a time, is the most cost-effective approach for a platform that shares the same basic front-end architecture across nearly two decades of production.

ItemTypical Detail
Vehicles coveredChrysler 300, Dodge Charger, Challenger, Magnum (2005–2023)
Drivetrain fitmentsRWD (2WD) and AWD — kits differ, must match
Kit component count8–14 pieces depending on configuration
Parts kit cost (aftermarket)~$2,100–$2,700
Labor cost (estimate)~$300–$600 at an independent shop
Alignment required after?Yes, always
End of productionDecember 2023 (Brampton, Ontario)

What Exactly Is a Front Suspension Kit for These Cars? The Chrysler 300 and Dodge Charger ride on the LX/LC rear-wheel-drive platform—one of the longest-running and most shared platforms in recent American automotive history. The Charger, Challenger, Magnum, and 300 all use the same basic front suspension layout, which means parts are heavily cross-listed. A proper front suspension kit for this family of cars typically includes:

  • Lower control arms (usually a pair, left and right)
  • Tension struts — these are the forward-pointing rods that control fore-aft movement of the lower control arm; their bushings are often the first thing to go
  • Ball joints — either pressed into the control arms or sold separately
  • Tie rod ends — inner and/or outer, depending on kit configuration

Some kits focus purely on the control arms and tension struts. Others bundle in tie rod ends to give you a genuinely comprehensive front-end refresh in one purchase. The piece count matters: an 8-piece kit might cover just the arms and struts, while a 14-piece kit goes further and addresses tie rod ends too. Neither is inherently better—it depends on what's actually worn on your car. ---

RWD vs. AWD: This Is Not a Small Detail

Here's where a lot of people get burned. The Chrysler 300 was offered in both rear-wheel-drive and all-wheel-drive configurations throughout its 2005–2023 production run. The Dodge Charger similarly offered AWD on certain trims. RWD and AWD kits are not interchangeable. The front knuckles differ, the geometry is different, and stuffing RWD control arms onto an AWD front end isn't going to work properly. Before you order anything, confirm your drivetrain. Check your door jamb sticker, the original window sticker if you have it, or simply look at whether there's a front driveshaft going into the differential. Most of the comprehensive front suspension kits you'll find—including MOOG's kits for this platform—are built for the RWD fitment. If you drive an AWD model, filter your search accordingly. ---

  • A clunk or knock when going over speed bumps, railroad tracks, or dipping in and out of driveways
  • The steering feels vague or the car wanders on the highway
  • Uneven front tire wear—scalloping, feathering, or inside-edge wear
  • The front end pulls to one side, especially under braking
  • Visible cracking or tearing in rubber bushings if you get under the car and look

Most owners on this platform hit trouble somewhere in the 80,000–120,000-mile range, though rough roads and spirited driving push that number lower. The 300 and Charger aren't small cars—curb weight ranges from roughly 3,900 to 4,400 lbs depending on trim and drivetrain—and that mass takes a toll on bushings and ball joints over time. ---

Why Replace Everything at Once? It's a fair question. If only the tension struts are bad, why not just do those? The honest answer: labor overlap. When you're already under the car with the front suspension disassembled, the incremental labor to swap control arms and tie rod ends at the same time is far less than making two separate appointments. Beyond that, if the tension strut bushings have degraded, there's a real chance the control arm bushings and ball joints have accumulated similar wear. Replacing only part of the system and then needing another alignment a year later costs more in the long run. In my experience looking at repair data and owner forum teardowns, the shops that do this job right the first time—full front-end refresh, one alignment—have far fewer comeback complaints than the ones that chase individual components. ---

What Brand Should You Buy? The kits in our inventory are from **MOOG**, and that's worth addressing honestly. MOOG has a long-established reputation as a suspension specialist. Their "Problem Solver" line is built around upgraded designs—greaseable ball joint fittings, reinforced housings, extended-life boots—intended to outlast what OEM put on from the factory. For a platform like the LX/LC, where tension strut bushings are a documented weak point, having greaseable joints that you can maintain is genuinely useful. MOOG kits for this platform range from 8-piece configurations (control arms + ball joints) up to 14-piece sets that include tie rod ends. If your tie rod ends are original and you're past 100,000 miles, the 12- or 14-piece kits make a lot of sense—not because it's a nice thing to do, but because tie rod ends on high-mileage cars in this weight class wear faster than most people expect. Use the part finder below to pull up the exact kit that matches your year, model, and drivetrain—the piece count and configuration vary, and getting the right fit matters. ---

A Note on This Platform's Legacy

The Chrysler 300 and Dodge Charger (V8/gas) both ended production after the 2023 model year. The final 300 rolled off the line in December 2023 at the Brampton, Ontario Assembly Plant—a genuine end of an era for a car that had been in continuous production since 2005. Both Chrysler and Dodge are currently owned by Stellantis N.V., the global automotive group that formed in January 2021 when Fiat Chrysler Automobiles merged with the French PSA Group. What this means practically: these cars aren't going away from roads anytime soon. There are millions of 300s and Chargers in daily use, the aftermarket is well-supplied, and brands like MOOG have broad coverage across the entire 2005–2023 production run. If you own one of these cars, you're not facing an orphaned-parts situation—the supply chain is solid. ---

What Does Installation Actually Involve? A front suspension kit on the LX/LC platform is a significant job. It's not a 45-minute driveway task. Here's what's involved:

  • Lift the car safely on jack stands—all four corners if you're doing both sides
  • Remove the front wheels
  • Disconnect the tension strut from the subframe and the control arm
  • Separate the ball joint from the knuckle (may require a separator tool or press depending on design)
  • Remove the control arm mounting bolts from the subframe
  • Install new components in reverse order, torquing everything to spec
  • Get a four-wheel alignment before driving the car normally

That last step isn't optional. Disturbing the control arm and tension strut geometry changes your caster, camber, and toe settings. Drive any real distance without an alignment and you'll toast a set of tires in short order. Experienced DIYers with proper tools can handle this. If you're not comfortable with suspension work, professional installation is the right call—just budget for both the parts and the labor. ---

Why buy from AutoBuffy

  • Fitment check: add your vehicle and we confirm the part fits before you buy. If it doesn't fit because of our listing, you get a free return and a full refund, including original shipping.
  • 24-month limited warranty on new parts bought on autobuffy.com.
  • Real reviews: rated 4.9 by 19,069 verified customers.
  • 30-day returns on unused parts in the original packaging.
  • Free shipping on orders $50+. Orders placed before 12:00 PM ET (Mon-Fri) ship the same business day.
  • Questions about an order? Call 888-477-2530 or email help@autobuffy.com.

Find the right suspension kit for your vehicle

Guaranteed fit, ships free

FAQ / People Also Ask

The modern Chrysler 300 ran from model years 2005 through 2023. Front suspension kits—lower control arms, tension struts, ball joints, and tie rod ends—are available across that entire production span, though hardware counts and exact fitment vary by year and drivetrain layout.

Need Parts for Your Car?

Shop quality auto parts with guaranteed fitment.

Shop Auto Parts

Comments

Sign in to join the discussion — commenting requires a free AutoBuffy account.

Loading comments...

Comments are moderated by the AutoBuffy team.