Do You Need an Alignment After Suspension Work?
Replacing struts? You almost certainly need an alignment. Replacing shocks? Probably not. Here's exactly when to book one — and why skipping it costs more.
The Short Answer
Yes — if you replaced struts or control arms, you need an alignment; if you only replaced shocks and disturbed nothing else, you probably don't.
| Work Performed | Alignment Required? | Which Wheels? |
|---|---|---|
| Front struts replaced | Yes | Front (minimum) |
| Rear struts replaced | Yes | Rear (minimum) |
| All four struts replaced | Yes | Four-wheel alignment |
| Front or rear shocks only | No (usually) | N/A |
| Control arms replaced | Yes | Affected axle, ideally all four |
| Coil springs replaced (new springs) | Yes | Affected axle |
| Coil springs reused on new strut | Recommended check | Affected axle |
Keep that table bookmarked — it covers 95% of the questions people have standing in their driveway wondering whether to book the shop. ---
Why Struts Change Your Alignment (and Shocks Don't)
This is the part most people get wrong, so it's worth being precise. A strut is a structural assembly. It combines the spring, the damper, and the steering pivot into one unit. When you pull a strut out and put a new one in, you've moved the geometry of that corner of the car. The wheel's camber angle (its vertical tilt), caster angle (the tilt of the steering axis front-to-back), and toe (whether the wheel points slightly in or out) can all shift in the process. A shock absorber is just a damper. It bolts to the existing suspension structure and doesn't integrate the spring or steering pivot. Swap it out without disturbing anything else, and the geometry stays where it was. Monroe® makes this official in their own service documentation: an alignment is recommended any time struts or other steering and suspension components are replaced. That's not a upsell — premature tire wear from a misaligned car is a real and predictable outcome. > "If you change the coil springs on a strut, this will alter the vehicle's height and camber angle." — Verified alignment guidance from suspension technical sources
The Three Angles You're Actually Protecting
When your shop does an alignment after strut work, they're measuring and correcting three things:
Camber
The vertical tilt of the wheel when viewed from the front of the car. A strut that's even slightly repositioned during installation can push camber out of spec, causing the inner or outer edge of your tire to wear down while the other side looks fine. ### Caster
The forward or backward lean of the steering axis. Caster affects straight-line tracking and steering return. You won't see it in your tires right away, but you'll feel the car pulling or fighting you on the highway. ### Toe
Whether your wheels point slightly inward (toe-in) or outward (toe-out) relative to the direction of travel. This is the one that destroys tires fastest — a toe angle that's even a fraction of a degree off eats rubber quickly and quietly. All three can be affected by strut replacement. All three need to be checked. ---
What About Control Arms? Control arms govern where your wheel sits relative to the chassis. Replace a control arm, and you've changed that relationship. It doesn't matter how carefully you torque everything to spec — the geometry of the new arm isn't guaranteed to match the worn geometry of the old one. The answer here is unambiguous: get an alignment after replacing control arms. If you're doing a more complete suspension refresh — replacing control arms alongside struts, ball joints, or tie rod ends — a four-wheel alignment isn't optional. It's the last step of the job. MOOG offers front control arm kits that bundle related components (tie rod ends, ball joints) into a single set, which makes sense when you're already in there. Replacing worn peripheral components at the same time prevents you from needing another alignment a few months later because a tie rod end finally gave out. ---
When You Can Skip the Alignment
There are a few legitimate scenarios where you don't need to book the shop:
- Rear shock replacement only, on a vehicle where the rear suspension uses shock absorbers (not struts), and nothing else was touched. Shocks don't change geometry. - Strut replacement with the original coil springs transferred over, where ride height hasn't changed. The disturbance is minimal. That said, getting a quick check is still cheap insurance — alignment checks at many shops run $20–$40 if no correction is needed. - Single-component replacements far from the steering axis, like a sway bar end link or a simple bushing, typically don't require a full alignment. The keyword is "disturbed." If you touched anything connected to where the wheel sits or steers, assume alignment is needed until proven otherwise. ---
Get It Done Immediately — Don't Wait
Some older advice suggested waiting for suspension components to "settle" before aligning. Most current technicians reject that. Get the alignment done right after the job. Every mile driven with misaligned geometry is tire wear you're not getting back. At $150–$300+ per tire, a $100–$175 four-wheel alignment is one of the better deals in automotive maintenance. If you're replacing struts front and rear, that's a full four-wheel alignment. Front struts only? At minimum a front-end alignment, though many shops will recommend four-wheel to confirm the rear is still in spec — especially on vehicles with adjustable rear geometry. ---
Budgeting for the Full Job
Here's a realistic cost picture so there are no surprises:
| Item | Typical Range |
|---|---|
| Front strut assembly (pair) | $150–$400 parts |
| Rear strut assembly (pair) | $120–$350 parts |
| Front control arm kit (with hardware) | $300–$800+ parts |
| Labor (struts, per axle) | $150–$350 |
| Four-wheel alignment | $100–$175 |
These are market ranges, not quotes. Dealer labor runs higher; a good independent shop can often do the full job for considerably less. The alignment is always the smallest line item — and skipping it risks the most expensive one (tires). ---
The Bottom Line
Replacing struts or control arms without getting an alignment is a false economy. The alignment is usually 10–15% of the total job cost and protects everything you just spent money on. Shocks are different — swap those without disturbing the suspension geometry and you're likely fine. If you're about to do suspension work, use the part finder below to get the right control arms and components for your specific vehicle before you start. Fit matters more than price when geometry is involved.
Why buy from AutoBuffy
- Fitment check: add your vehicle and we confirm the part fits before you buy. If it doesn't fit because of our listing, you get a free return and a full refund, including original shipping.
- 24-month limited warranty on new parts bought on autobuffy.com.
- Real reviews: rated 4.9 by 19,069 verified customers.
- 30-day returns on unused parts in the original packaging.
- Free shipping on orders $50+. Orders placed before 12:00 PM ET (Mon-Fri) ship the same business day.
- Questions about an order? Call 888-477-2530 or email help@autobuffy.com.
- Shop or fleet? Call 301-463-4380 for shop pricing.
Find the right control arm for your vehicle
Guaranteed fit, ships free
FAQ / People Also Ask
Yes. Struts are structural components that directly affect camber, caster, and toe angles. Monroe® officially recommends an alignment any time struts are replaced. Skipping it leads to uneven tire wear and compromised handling.





Comments
Loading comments...
Comments are moderated by the AutoBuffy team.