How to Replace a Control Arm: Step-by-Step Guide
How-To GuidesNov 17, 2026•8

How to Replace a Control Arm: Step-by-Step Guide

Learn how to replace a control arm safely, with the right tools, torque specs, and pro tips that shops don't always share.

By AutoBuffy Team

Share:

The Short Answer

Replacing a control arm means unbolting the arm from the subframe and steering knuckle, swapping in the new assembly, and—critically—torquing the bushing hardware only after the suspension is back at ride height, followed by a professional wheel alignment.

StepWhat You're DoingTime Estimate
1. Lift & support vehicleJack up, set stands at approved lift points15 min
2. Remove wheelStandard lug removal10 min
3. Disconnect ball jointSeparate from knuckle with ball joint tool20–40 min
4. Unbolt arm from subframeRemove pivot bolts/bushings20–30 min
5. Install new armHand-thread all hardware first20 min
6. Lower to ride height, torqueSnug all bushing bolts at ride height20 min
7. Reinstall wheel, lower carFinal torque on lug nuts10 min
8. Get alignmentNon-negotiable after this job45–90 min

Total DIY time per side: roughly 2–4 hours, more if rust is fighting you. ---

What a Control Arm Actually Does

The control arm is the link between your vehicle's frame (or subframe) and the wheel hub. It lets the wheel move up and down over bumps while keeping it from moving in directions it shouldn't. Two rubber or polyurethane bushings cushion the pivot points at the frame end, and a ball joint connects the outer end to the steering knuckle. When any of those three connection points—inner bushings, outer bushing, or ball joint—wear out, you get the classic symptoms: clunking over bumps, a steering wheel that shimmies, or a car that drifts on a straight road. A worn ball joint is the urgent one. It can separate under load, and that's not a situation you want to be in at highway speed. ---

Tools and Parts You'll Need Before You Start

Don't start tearing into the suspension without everything on hand. Mid-job parts runs waste time and leave your car sitting on stands overnight. Tools:

  • Floor jack and a minimum of two quality jack stands
  • Breaker bar and impact wrench (optional but helpful)
  • Torque wrench — this is not optional
  • Ball joint separator (press-style preferred over a pickle fork if you're reusing the knuckle boot)
  • Metric and SAE socket sets
  • Penetrating oil (spray the pivot bolts a day in advance if possible)
  • Wire brush for cleaning threads

Parts:

  • New control arm for your exact application — arms aren't universal
  • Replacement hardware if not included (some bolts are torque-to-yield and shouldn't be reused)
  • New cotter pin if your ball joint uses one

For parts, MOOG offers complete front suspension kits that bundle control arms with tie rod ends or ball joints — a smart buy if your neighboring components have high mileage. Similarly, Dorman Products (a publicly traded independent company headquartered in Colmar, Pennsylvania, trading on NASDAQ as DORM) designs and distributes a wide catalog of control arm assemblies covering light-duty and heavy-duty applications. Both brands are worth checking for your specific vehicle. Use the part finder below to confirm fitment before you order anything. ---

Safety First: The Rules That Actually Matter

Let's be blunt about two things:

  • Never work under a vehicle supported only by a floor jack. A jack is for lifting. Jack stands — placed at manufacturer-approved lift points — are what hold the car while you're under it. No exceptions. 2. Torque your bushing bolts at ride height, not in the air. This is the mistake that sidelines even experienced DIYers. When you tighten the pivot bolts while the suspension is hanging, you're twisting the rubber bushing into a stressed position. Every time the suspension cycles after that, it's fighting to unwind. The result is premature bushing failure, often within a year. Lower the car onto its wheels (or use a floor jack to simulate ride height under the control arm) before you put a torque wrench on those bolts. ---

Step-by-Step: How to Replace a Control Arm

Step 1 – Loosen Lug Nuts, Then Lift

Break the lug nuts loose while the tire is still on the ground — it's much easier. Then jack the vehicle up, place jack stands at the correct lift points, and finish removing the wheel. ### Step 2 – Soak the Hardware

If your vehicle has any years on it, hit the pivot bolts and ball joint nut with penetrating oil now and give it 10–15 minutes to work. Seized hardware is the #1 reason this job runs long. ### Step 3 – Disconnect the Ball Joint

The ball joint nut often has a cotter pin — remove it first. Back off the nut but don't remove it completely yet. Use your ball joint separator to pop the joint loose from the steering knuckle. Once it breaks free, remove the nut entirely and push the stud out of the knuckle. > Pro tip: A press-style separator is gentler on the boot than a pickle fork. If you're replacing the whole arm assembly anyway, a pickle fork is fine — you're not saving that boot. ### Step 4 – Remove the Pivot Bolts at the Subframe

These are the bolts that hold the inner end of the arm to the subframe. On many vehicles there are two — one at each bushing. They can be stubborn. A long breaker bar or impact wrench will help. Keep track of any washers, spacers, or cam bolts — those affect alignment and need to go back in the same orientation. Note any cam bolts or eccentric adjusters. Take a photo before removal. Your alignment tech will thank you. ### Step 5 – Remove the Old Arm

With the ball joint disconnected and the pivot bolts out, the arm drops free. Compare it to the new one — length, bushing diameter, ball joint position. They should match. If they don't, you've got the wrong part. ### Step 6 – Install the New Arm

Thread all hardware in by hand first. Don't tighten anything yet. Get the pivot bolts started at the subframe, and get the ball joint stud seated in the knuckle with the nut hand-tight. Install a new cotter pin if required. ### Step 7 – Torque at Ride Height

This is the critical step. Lower the vehicle so the suspension bears the car's weight, or use a floor jack under the outer end of the control arm to load it. Now torque the pivot bolts to spec. Check your service manual or a reliable source for your specific vehicle — specs vary widely by application, typically ranging from 80–150 ft-lbs for lower arm pivot bolts, but don't guess. Torque the ball joint nut to spec as well and install any required cotter pin. ### Step 8 – Reinstall the Wheel and Lower the Car

Standard wheel installation. Torque the lug nuts to spec in a star pattern. ### Step 9 – Get a Wheel Alignment

This is not optional, and it's not just a formality. Removing the control arm changes your camber and caster angles. Drive it to an alignment shop before you put any real miles on it. Skipping this step will wear your new tires unevenly within a few thousand miles. ---

Should You Replace Just One Arm or the Whole Set? Replacing a single arm is completely legitimate if the other side is in good shape. Inspect it — grab the wheel at 12 and 6 o'clock, rock it and check for play. Do the same at 9 and 3. If there's no slop and the bushings look intact, one side is fine. That said, if you're already doing the work and both sides have high mileage, a complete suspension kit (arms, tie rod ends, ball joints together) often makes more economic sense than going back in six months for the other side. ---

Choosing the Right Control Arm Brand

MOOG's automotive aftermarket lineup — distributed through Moog Louisville Warehouse, which was acquired by Auto-Wares — offers complete suspension kits that pair control arms with tie rod ends or ball joints in a single box. That's genuinely convenient for a full front-end refresh. Dorman is a solid alternative, particularly for applications where OE-style direct-fit replacements are the priority. They cover an enormous range across light duty, heavy duty, and specialty vehicles. Neither brand is automatically "the right answer" — it depends on your vehicle and what's available for your fitment. Use the part finder below to see what's actually in stock for your year, make, and model. ---

Why buy from AutoBuffy

  • Fitment check: add your vehicle and we confirm the part fits before you buy. If it doesn't fit because of our listing, you get a free return and a full refund, including original shipping.
  • 24-month limited warranty on new parts bought on autobuffy.com.
  • Real reviews: rated 4.9 by 19,069 verified customers.
  • 30-day returns on unused parts in the original packaging.
  • Free shipping on orders $50+. Orders placed before 12:00 PM ET (Mon-Fri) ship the same business day.
  • Questions about an order? Call 888-477-2530 or email help@autobuffy.com.
  • Shop or fleet? Call 301-463-4380 for shop pricing.

Find the right control arm for your vehicle

Guaranteed fit, ships free

FAQ / People Also Ask

For a moderately experienced DIYer, plan on 2–4 hours per side. Rust, seized hardware, or a press-in ball joint can push that to a full day. A shop will typically quote 1.5–3 labor hours per arm.

Need Parts for Your Car?

Shop quality auto parts with guaranteed fitment.

Shop Auto Parts

Comments

Sign in to join the discussion — commenting requires a free AutoBuffy account.

Loading comments...

Comments are moderated by the AutoBuffy team.